SKF Bearing housings

The SKF SY pillow block with insert bearing is an assembled unit that combines a cast iron housing with a Y-series insert bearing. It is used to support rotating shafts in transmission equipment, especially when simple mounting and self-alignment are required. MR Accesorios Industriales carries this line as an official brand for industrial applications in Argentina.

The SY …. TF designation is read as follows: SY identifies the split pillow block housing with insert bearing; the number that follows indicates the shaft diameter, in inches or millimeters as applicable; and the TF suffix indicates the locking system of the insert to the shaft, which in this series is by set screws. For example, SY 1. TF corresponds to a 1 inch shaft, while SY 1.1/2 TF is for 1 1/2 inches. The suffix does not change the housing dimensions, but it does change the bearing adjustment method.

These pillow blocks are used in belt conveyors, bucket elevators, mixers, mills, screens and process equipment in food, chemical and aggregate plants. They also appear in agricultural machinery, centrifugal pumps and industrial fans. In Argentina they are common in grain plants, meat processing plants and animal feed factories, where quick mounting and simple insert replacement are key to avoiding production stoppages.

To choose the correct pillow block, verify the shaft diameter and the locking type required by your equipment. The insert seal can be simple or with an additional lip seal for dusty or humid environments. The internal clearance of the insert bearing is greater than that of a conventional deep groove ball bearing, which allows for some misalignment. During mounting, make sure the base sits properly and that the locking screws are tightened with the appropriate wrench. Lubrication is done through a grease nipple and the manufacturer's frequency should be followed.

Regarding equivalences, SKF SY pillow blocks are interchangeable with other brands that use the same mounting standard and shaft diameter, such as NTN's SY series, NSK's FY series or Timken's UC series, provided the main dimensions and locking type match. Do not invent codes: if you have doubts, send us the original code and we will confirm the equivalence. Interchangeability is not always complete: verify tolerances and sealing before replacing.

If you need a quote for an SKF SY pillow block with insert bearing, write to us on WhatsApp and send the complete code, for example SY 1.1/4 TF. At MR Accesorios Industriales we advise you to choose the correct variant for your application. With more than 80 years in the market, we know the needs of Argentine industry and give you a technical and direct response.

The SKF FY . TF Y-bearing housed unit is an assembled unit that combines a split housing with a Y-series insert bearing. It is used to mount rotating shafts in machine structures, with the advantage that the bearing comes already housed and lubricated. It is a practical solution for power transmission in industrial equipment, where robustness and ease of assembly are required.

The designation FY …. TF is read as follows: FY identifies the SKF Y-bearing housing category; the number that follows indicates the nominal shaft diameter in inches, with fractions expressed in sixteenths. For example, FY 1. TF is for a 1-inch shaft, FY 1.1/2 TF for 1 1/2 inches, FY 1.1/4 TF for 1 1/4 inches, and FY 1.3/16 TF for 1 3/16 inches. The suffix TF indicates that the insert bearing has a design with specific sealing and locking features, which vary by version. To confirm the exact configuration of each part number, check the corresponding product page.

These housed units are used in a wide variety of industrial applications in Argentina: belt conveyors, bucket elevators, mixers, mills, centrifugal pumps, fans, machines for the food, textile, wood and cement industries. They also appear in continuous process equipment, where ease of assembly and the ability to support combined loads are important. Their split design allows the shaft to be mounted without disassembling other components, which simplifies plant maintenance.

To correctly select an FY . TF housed unit, take into account the shaft diameter, the type of load (radial, axial or combined), the environmental conditions and the rotation speed. The insert bearing usually comes with seals that retain lubricant and block contaminants; verify that the sealing is suitable for dust, moisture or frequent washdowns. During assembly, ensure correct alignment between housings and avoid striking the insert. Life-long lubrication is common in these units, but in severe environments it may require periodic relubrication.

Regarding equivalents and interchangeability, Y-bearing housed units from different brands may be similar in dimensions, but they are not always directly interchangeable. Differences in the insert-to-shaft locking system, in the seals or in the housing tolerance can affect performance. It is always advisable to verify the critical dimensions and service conditions before replacing one brand with another. If you need guidance, at MR Accesorios Industriales we can help you find the right alternative.

To request a quote for the housed unit you need, send us the complete part number by WhatsApp. If you do not have it at hand, send us the shaft diameter, the type of load and the working conditions, and we will advise you. At MR Accesorios Industriales we sell official brands and have more than 80 years of experience in the industry.

The SKF Y-bearing housing with insert bearing of the UCP series is an assembly made up of an insert bearing with spherical outer ring and a cast iron housing with flat base and two mounting holes. It is used to mount rotating shafts on welded or bolted structures, with self-alignment that compensates for small mounting errors. It is a practical solution for belt, chain or coupling drives in industrial equipment.

The UCP designation reads as a Y-bearing housing with insert bearing: the U indicates the complete unit, the C the housing type with cast iron base and the P the bolt-on mounting variant. The number that follows, as in UCP 204 or UCP 208, identifies the size of the insert bearing and defines the main dimensions of the assembly. When a hyphenated suffix appears, for example UCP 205-16 or UCP 206-19, the additional number indicates the shaft diameter in sixteenths of an inch, an option for shafts in imperial measurement.

In Argentine industry, UCP housings are found in belt conveyors, bucket elevators, mixers, mills, screens and packaging lines. They are also used in pumping, ventilation and belt drive equipment, where mounting on metal structures requires a compact and easy-to-install unit. As a standard component, it allows insert bearings to be replaced without modifying the housing, which simplifies maintenance in food, cement, mining and chemical plants.

To select a UCP housing, take into account the shaft diameter, the type of load (radial, axial or combined) and the environmental conditions. The insert bearing comes factory-lubricated and protected with seals that retain grease and block contaminants; in dusty or humid environments, it is advisable to verify the sealing type and plan a periodic lubrication schedule. Mounting requires the base to rest on a flat, rigid surface, with the bolts tightened evenly so as not to deform the housing. The self-alignment of the insert absorbs small angular deviations, but does not replace correct leveling.

Y-bearing housings with insert bearing are interchangeable between manufacturers when the main dimensions and shaft diameter match. The SKF UCP series can be replaced by equivalent units from other brands that follow the same mounting standard, although tolerances and sealing may vary. To ensure compatibility, it is advisable to compare the housing dimensions, the hole positions and the insert mounting type. MR Accesorios Industriales sells this line as an official brand, with technical advice to choose the right unit.

If you need a Y-bearing housing with insert bearing for your equipment, send us the full part number via WhatsApp. At MR Accesorios Industriales we help you identify the correct unit according to the shaft diameter and mounting type. With more than 80 years in the business, we answer technical inquiries and quote the UCP series and its alternatives.

FRB covers are axial locating components placed in split bearing housings to retain the outer ring and prevent displacement. They are used in equipment with shafts that transmit mainly radial loads, where the bearing must remain positioned without blocking thermal expansion. MR Accesorios Industriales supplies this SKF line in Buenos Aires, Argentina, with advice to choose the correct size according to the housing and the mounted bearing.

The FRB designation reads as a category of standardized covers: the letters identify the series and the numbers that follow indicate the bearing outer diameter and the housing width. For example, FRB 2/120 corresponds to a cover for a bearing with a 120 mm outer diameter, while FRB 3.5/52 and FRB 3.5/72 share the same housing width (3.5) and vary in diameter. Likewise, FRB 4/62, FRB 4/80 and FRB 4/90 belong to the width 4 series. This logic allows you to quickly identify the cover that fits an SKF split housing.

These covers are used in a wide variety of industrial applications in Argentina: grain and mineral conveyors, mills, mixers, centrifugal pumps, fans, conveyor belts and process equipment in food and beverage plants. They also appear in old or hard-to-access machines where a damaged cover needs to be replaced without changing the complete housing. As a locating component, their function is to keep the bearing in position and simplify assembly and disassembly of the unit.

To select the correct cover, take into account the bearing outer diameter and the width of the split housing. The FRB designation already includes both data, but it is advisable to verify that the housing is compatible with the series. During assembly, make sure the contact surfaces are clean and free of burrs, and that the cover seats evenly. Bearing lubrication does not depend on the cover, but an incorrectly placed cover can allow contaminants to enter. Always follow the equipment manufacturer's instructions.

SKF FRB covers can be interchanged with those from other manufacturers that use the same standardized designation, although tolerances and surface treatment may vary. Therefore, when replacing a cover, it is advisable to compare the critical dimensions and the material. At MR Accesorios Industriales we can guide you on the equivalence with other brands, without the need to change the housing. Interchangeability is possible when the outer diameter and width match, but always verify the fit on the equipment.

If you need an FRB cover for your housing, send us the complete code via WhatsApp. At MR Accesorios Industriales we advise you so that you choose the correct size and we quote the one you need. With more than 80 years in the industry, we know the housings and their accessories.

TSN A end covers are closing components for split bearing housings. They are fitted on both sides of the housing and serve two functions: retaining the lubricant inside the cavity and preventing the entry of dust, water or particles. They are the usual choice when the housing is exposed to environments with moderate dirt or moisture. At MR Accesorios Industriales we supply them as part of our line of accessories for SKF housings.

The TSN designation identifies the family of end covers for split housings. The number that follows —for example, in TSN 206 A, TSN 210 A or TSN 213 A— relates to the size of the housing they are combined with. The suffix A distinguishes a construction variant within the series. To choose the correct end cover, the safest approach is to start from the part number of the housing already installed or of the bearing to be housed, and verify compatibility with that reference.

These end covers are used in equipment where the housing is exposed to the weather or in dusty areas: conveyor belts, bucket elevators, mills, mixers, centrifugal pumps and industrial fans. In food, cement, mining, aggregate processing and agro-industrial plants in Argentina, the additional sealing they provide helps extend bearing life and reduce relubrication frequency.

When selecting a TSN A end cover, check that the diameter and shape of the housing match the end cover. The end cover is fastened with the same bolts as the housing or with its own bolts, depending on the design. It is important that the sealing lip rests evenly on the shaft and is not misaligned. Proper lubrication of the cavity and the use of the end cover on both sides of the housing improve lubricant retention and protection against contaminants.

SKF TSN A end covers can be interchanged with those from other manufacturers offering equivalent end covers for split housings, provided the mounting dimensions and the type of sealing match. It is not enough for the end cover number to be similar: the outside diameter, the shaft bore and the fastening system must be compared. If you have doubts, send us the housing part number and the bearing part number, and we will verify it.

To request a quote for TSN A end covers, send the full part number by WhatsApp to MR Accesorios Industriales. If you do not have it at hand, a photo of the housing or the main dimensions is enough. We work with the SKF line of housings and accessories and can guide you toward the end cover that corresponds to your equipment.

TSN S end covers are closure components for split bearing housings. They are placed at the ends of the housing and serve two functions: retain lubricant inside the cavity and prevent the ingress of dust, water or particles. The SKF TSN S series is used in applications where the bearing operates in environments with moderate contamination. MR Accesorios Industriales supplies this line as part of its range of housings and accessories.

The TSN S designation is read as a category of end covers for split housings. The number following TSN indicates the size of the housing it is compatible with: for example, TSN 208 S corresponds to a housing for a 40 mm shaft bearing, while TSN 220 S is used in housings for larger diameter shafts. The final letter S distinguishes this variant within the TSN series. To choose the correct end cover, you must cross-reference the code with the housing you already have installed.

These end covers are used in transmission equipment, conveyors, mixers, pumps and industrial fans. In Argentina, they are common in food processing plants, cement plants, paper mills and in the mining sector, where split housings facilitate assembly and disassembly. They also appear in agricultural machinery and in production lines that require frequent maintenance. The TSN S end cover helps extend bearing life by keeping lubrication clean.

To select the end cover, verify the shaft diameter and the housing code. The end cover must match the groove and holes of the housing. During assembly, make sure the sealing lip faces outward and is free of deformation. Alignment between end cover and housing is key to preventing leaks. If the environment has high humidity or dust, consider an end cover with greater protection. Bearing lubrication should be done before closing with the end cover.

SKF TSN S end covers can be interchanged with equivalents from other brands that follow the same split housing standard. However, groove and hole dimensions may vary slightly between manufacturers. Therefore, it is always advisable to compare the code and actual measurements before replacing. MR Accesorios Industriales can advise you on compatibility with the housing you have. Not all end covers in the TSN series are the same: the final S indicates a specific configuration.

If you need TSN S end covers for your housings, send us the complete code via WhatsApp. At MR Accesorios Industriales we provide a quote based on the size and quantity you need. We can also help you identify the correct end cover if you send us a photo of the housing or the code engraved on the part. We work with in-house manufacturing to give you a comprehensive solution in bearings and accessories.

The SNL split plummer block housing is a housing split horizontally into two or three pieces, designed to hold a spherical roller bearing. The split design allows it to be mounted and removed without having to take out the entire shaft, which is key on long or heavy shafts where that is not always possible.

The SNL designation is followed by a three-digit number that identifies the size of the base and of the bearing it holds, and sometimes by suffixes that indicate sealing variants, housing material or the position of the locating plate. The same housing number is often combined with different bearings depending on the exact shaft diameter you need.

It is used in belt conveyors, large industrial fans, mills, mixers and in general on any long horizontal shaft that needs a support point in the middle or at the ends, especially when the shaft may have some misalignment due to deflection or mounting tolerance.

The self-aligning bearing inside is what gives the assembly the ability to tolerate angular misalignment of the shaft without transmitting that misalignment as extra load to the rollers. When ordering the replacement, it is best to confirm both the housing number and the bearing mounted inside it, because it is not always the same in different installations.

The SNL series, with its two- or three-piece system and its standard base, has equivalents of comparable size from other split housing manufacturers, although the sealing system and construction variants change from one brand to another. Confirm the complete housing number before ordering an equivalent, because the same base number can have variants in height or hole position.

Send us the housing number —or the shaft diameter if you do not have it— by WhatsApp and we will confirm which bearing it takes and the available alternatives. MR Accesorios Industriales quotes SKF SNL housings and equivalents.

The SNL split plummer block housing from SKF is an essential component for mounting bearings in industrial applications. Its two-piece design facilitates installation and maintenance, allowing the bearing to be replaced without dismounting the shaft. Made of high-quality cast iron, it offers robustness and durability. It is ideal for transmitting radial and axial loads in rotating equipment, and its use is widespread in various industries that require reliability and efficiency.

The SNL designation is interpreted as follows: the letters SNL indicate a split plummer block housing of the SNL series. The first number, for example 508, indicates the housing size and the shaft diameter for which it is designed. The suffix after the slash, such as VU801, identifies specific variants, such as the type of sealing or additional features. For example, SNL 508-607/VU801 corresponds to a housing for a 1 7/16 inch shaft with VU801 sealing. It is essential to verify the complete part number to ensure compatibility with the bearing and the application.

These housings are used in a wide range of industries in Argentina, such as food, cement, mining, petrochemical and material handling. They are common in conveyors, mills, mixers, pumps and fans. Their ability to support combined loads and their ease of mounting make them ideal for demanding environments. In production plants, they are preferred for their speed of installation and the possibility of inspecting the bearing without disassembling the entire assembly.

To select the appropriate housing, it is crucial to consider the type of bearing (deep groove ball bearing, cylindrical roller bearing, etc.), the shaft diameter and the operating conditions. The VU sealing protects against contaminants and retains the lubricant. During mounting, ensure correct alignment between the halves and the shaft to avoid additional loads. Lubrication must be suitable for the bearing and the environmental conditions. Check the internal clearance and adjust according to the manufacturer's recommendations.

Regarding equivalences, SKF SNL housings can be interchanged with products from other brands that follow the same dimensional standard. However, it is important to verify tolerances and materials, as they may vary between manufacturers. Always consult with us to confirm compatibility. At MR Accesorios Industriales we sell SKF as an official brand, and we can advise you on the best option for your equipment.

To obtain a quote or personalized advice, send the complete part number of the housing you need via WhatsApp to MR Accesorios Industriales. Our technical team will respond shortly with the required information. We work with the leading brands and have more than 80 years of experience in the field, guaranteeing a quality service.

El soporte bipartido SNL de SKF es un componente fundamental para el montaje de rodamientos en aplicaciones con ejes que giran. Su diseño de dos piezas permite un montaje y desmontaje sencillo sin necesidad de desarmar el eje, lo que simplifica el mantenimiento. Se utiliza ampliamente en equipos de transmisión de potencia, transportadores y maquinaria industrial. MR Accesorios Industriales comercializa esta línea con el respaldo técnico de más de 80 años en el rubro.

La designación de los soportes SNL sigue un esquema claro. Por ejemplo, SNL 212 K7 indica un soporte de la serie SNL con tamaño 212 y un sufijo K7 que define variantes de sellado y fijación. En SNL 509 K7, el número 509 corresponde a un tamaño específico para ejes de menor diámetro. La serie SNL abarca múltiples tamaños y configuraciones; los sufijos como K7, K8 o similares indican el tipo de sello y el método de fijación, aspectos clave para adaptar el soporte al entorno de trabajo.

Estos soportes se emplean en una amplia variedad de industrias en Argentina: desde plantas alimenticias y embotelladoras hasta la industria metalúrgica, cementera y de manejo de materiales. Son comunes en transportadores de banda, elevadores de cangilones, mezcladoras, molinos y ventiladores industriales. Su capacidad para soportar cargas radiales y axiales moderadas los hace versátiles. Además, su diseño bipartido facilita las tareas de mantenimiento en equipos donde el acceso es limitado.

Para seleccionar el soporte adecuado, tené en cuenta el diámetro del eje, el tipo de rodamiento a montar (habitualmente rodamientos rígidos de bolas o de rodillos cilíndricos), y las condiciones ambientales. El sellado es crítico: los sufijos K7 suelen incluir sellos de labio que protegen contra polvo y humedad. La lubricación debe ser la adecuada para la velocidad y carga. La alineación correcta durante el montaje evita esfuerzos parásitos y prolonga la vida útil del rodamiento.

En cuanto a equivalencias, los soportes SNL de SKF pueden intercambiarse con productos de otros fabricantes que sigan la misma norma de dimensiones. Es fundamental verificar las dimensiones de montaje y el tipo de rodamiento compatible. En MR Accesorios Industriales podemos asesorarte sobre la intercambiabilidad y las alternativas disponibles. Siempre recomendamos confirmar el código exacto y las especificaciones técnicas antes de reemplazar un componente.

Para cotizar el soporte bipartido SNL que necesitás, simplemente envianos el código por WhatsApp. En MR Accesorios Industriales te brindamos atención personalizada y te ayudamos a identificar la referencia correcta según tu equipo. Con más de 80 años de experiencia, somos tu socio confiable en componentes industriales. Escribinos y te responderemos a la brevedad.

The SAF housing is a cast iron split plummer block housing, more robust and larger than an equivalent SNL, designed for high loads and larger diameter shafts. Like the SNL, it splits apart so it can be mounted without dismantling the entire shaft, but its base and cap are sized to work with more margin.

The SAF designation is followed by a three-digit number that identifies the size, and some codes add sealing or grease nipple position suffixes. The housing is combined with a spherical roller bearing, which is ordered according to the exact shaft diameter.

It is used in heavy conveyors, mills, crushers, large industrial fans and mining equipment, where the load and shaft size exceed what a standard SNL housing covers. It is common in installations with large diameter shafts running 24 hours a day.

Because of the size and the load they handle, the cap fit and the sealing system are especially important: a badly sealed SAF lets dust or water in on installations that are often outdoors, such as mineral or agro-industrial conveyor belts.

As with the SNL, the SAF series has comparable-size equivalents from other cast iron split plummer block housing manufacturers. Confirm the full number and the shaft diameter before ordering an equivalent.

Send us the housing number or the shaft diameter by WhatsApp and we will confirm the corresponding bearing and the alternatives available. MR Accesorios Industriales gives quotes for SAF housings by manufacturer code.

The SKF SAF split housing is a key component for mounting bearings on shafts, as it allows easy assembly and disassembly without dismantling the entire equipment. Its robust and versatile design makes it ideal for industrial applications requiring high reliability and ease of maintenance. MR Accesorios Industriales supplies this line backed by more than 80 years in the Argentine market.

The SAFS designation is interpreted as follows: the letters SAF indicate that it is a split housing for bearings, and the final S indicates that it is designed for shafts with larger diameter and higher load capacities. The number that follows, as in SAFS 218-11 or SAFS 236, corresponds to the size of the bearing it houses, and in some cases a numeric suffix is added to indicate design variants, such as the position of the lubrication groove or the type of sealing. For example, SAFS 520 and SAFS 522 are specific sizes for larger diameter shafts. Knowing these codes is key to selecting the correct housing.

These housings are used in a wide variety of industrial applications in Argentina, such as conveyors, mills, mixers, pumps, fans and processing equipment in food, cement, mining and oil plants. Their split design allows mounting the bearing on the shaft and then securing it with the housing, which simplifies maintenance tasks and reduces downtime. They are especially useful in equipment where access is limited or where the bearing needs to be replaced without disassembling other components.

To select an SAFS housing, take into account the shaft diameter, the type and size of bearing it will house, and the operating conditions. It is essential to verify alignment between the housing and the shaft to avoid additional loads and premature wear. Sealing is another critical aspect: choose the appropriate seal type according to the environment (dust, humidity, temperature). Lubrication must be the recommended one for the bearing and service conditions. In addition, assembly must be carried out with the appropriate tools and following the manufacturer's instructions to ensure reliable operation.

Regarding equivalences and interchangeability, SKF SAF housings are compatible with bearings from other brands that follow the same standardized dimensions. However, it is important to verify tolerances and load capacities to ensure a correct fit. MR Accesorios Industriales offers technical advice to find the best solution according to your needs. If you need to replace an existing housing, we can help you identify the equivalent code and verify compatibility with your equipment.

To request a quote for the SAF split housing you need, simply send us the complete code via WhatsApp. At MR Accesorios Industriales we advise you so you choose the correct option and provide the technical support your application requires. Do not hesitate to contact us; our team is ready to help you.

The SAF split plummer block housing is a bearing mounting component that is assembled in two halves, which facilitates installation and maintenance on transmission shafts. It is used to support radial and axial loads in rotating equipment, allowing the accommodation of bearings with tapered or cylindrical inserts. Its robust and versatile design makes it ideal for demanding industrial applications. MR Accesorios Industriales carries this SKF line, an official brand that MR carries, with more than 80 years of experience in the field.

The designation FSAF followed by a number identifies the size and series of the housing. For example, FSAF 216 corresponds to a housing for a shaft with a nominal diameter of 16 inches, while FSAF 313 indicates a size for a 3 3/16 inch shaft. The numbers are not sequential and respond to standardization standards. In the SAF series, the suffix can indicate variants such as sealing or mounting configuration. To choose the correct one, it is essential to verify the shaft diameter and the type of bearing to be used.

These housings are used in a wide variety of industries in Argentina, such as food, cement, mining, petrochemical and materials handling. They are found in conveyors, mills, mixers, pumps, fans and gear reducers. Their ability to withstand combined loads and moderate misalignments makes them suitable for environments with dust, humidity or variable temperatures. The split construction allows the bearing to be replaced without disassembling the shaft or the complete equipment, reducing downtime.

For proper selection, take into account the shaft diameter, radial and axial load, and environmental conditions. Sealing is key: choose labyrinths or oil seals depending on contamination. Lubrication can be with grease or oil; verify the method and frequency. Mounting requires aligning the halves and tightening the bolts uniformly to avoid deformation. It is advisable to follow the manufacturer's instructions and use appropriate tools to avoid damaging the bearing during installation.

Regarding equivalences, SKF SAF housings are interchangeable with those of other brands that follow the same dimensional standards, such as the SAF series from Timken or Dodge. However, always verify the exact dimensions and load capacity before replacing. Part numbers may vary between manufacturers, so it is essential to compare technical specifications. At MR Accesorios Industriales we can advise you to find the right replacement for your application.

If you need an SAF split plummer block housing, contact us on WhatsApp and send us the part number or the measurements of your equipment. Our technical team will help you identify the correct product and provide you with a no-obligation quote. With more than 80 years of experience, at MR Accesorios Industriales we offer reliable solutions for your power transmission systems.

The SKF SSNLD split housing is a solid-base component that houses and secures bearings in rotating equipment. Its two-half design facilitates assembly and disassembly without dismantling the shaft, simplifying maintenance. It is used in conveyors, mills, pumps and fans, among other industrial applications. MR Accesorios Industriales distributes this SKF line in Buenos Aires, Argentina.

The SSNLD designation is interpreted in blocks: SS indicates a solid-base split housing; NLD defines the series and the type of fixing. The suffixes /MS1 and /MS2 refer to sealing or fixing variants. For example, SSNLD 216/MS2 corresponds to a housing for a 216 mm shaft, while SSNLD 510-608/MS1 and SSNLD 511-609/MS1 are inch or combined sizes. Always verify the complete code with MR before requesting a quote.

In Argentine industry, these housings are used in conveyor belts in grain plants, flour mills, centrifugal pumps, industrial fans and process equipment. Their solid base absorbs loads and vibrations, and the split design allows replacing the bearing without moving the shaft or the transmission. They are common in food, chemical, cement and mining plants, where robustness and ease of maintenance are critical.

To select the housing, consider the shaft diameter, the bearing type (usually spherical roller bearing), radial and axial loads, and environmental conditions. The MS1 or MS2 sealing defines the degree of protection against dust and moisture. During assembly, ensure alignment of the halves and uniform tightening of the bolts; lubricate according to the bearing and verify clearance. Correct installation extends the service life of the assembly.

SKF SSNLD housings are interchangeable with other brands that follow the same dimensional and fixing standard, such as those of the SNL or SSN series from other manufacturers. However, tolerances and seals may vary. For replacements, always compare the complete code and critical dimensions. MR Accesorios Industriales can advise you on the appropriate equivalent for your application.

If you need an SKF SSNLD split housing, send us the exact code via WhatsApp. At MR Accesorios Industriales we help you identify the correct variant and request a quote. More than 80 years of experience in industrial distribution back us.

The SKF split plummer block housing from the SSNLD line is a solid base component that houses and secures bearings in equipment with rotating shafts. Its split design allows mounting and dismounting without dismantling the shaft, which simplifies plant maintenance. It is used in conveyors, mills, pumps and industrial fans. MR Accesorios Industriales supplies this line with technical advice to select the right variant.

The SSNLD designation is read in blocks: the letters indicate the split plummer block housing with solid base category; the first number identifies the size and the combination of diameters; the NM or MS suffix defines the sealing type and the bearing series it houses. For example, SSNLD 216 NM/MS2 corresponds to a housing for a 16-inch shaft with NM sealing and series 2 bearing, while SSNLD 516-613 NM/MS1 combines two shaft sizes in the same housing. Understanding this logic prevents errors when ordering spare parts.

In Argentine industry, these housings appear in belt conveyors, flour mills, centrifugal pumps, induced draft fans and mixers. Their solid base absorbs combined loads and vibrations typical of heavy equipment. Being split, they adapt to existing shafts without the need to remove pulleys, couplings or complete drives, which reduces downtime in food, cement, mining and aggregate processing plants.

To select the housing, verify the shaft diameter, radial and axial load, and environmental conditions. The NM or MS sealing defines the degree of protection against dust and humidity: choose the most closed one in dirty environments or with frequent washdowns. Check the alignment between housings and the bearing internal clearance during mounting; proper lubrication and progressive tightening of the connecting screws ensure service life. The solid base requires a flat, rigid surface to avoid deformation.

SKF SSNLD housings are interchangeable with other brands that use the same mounting standard and shaft dimensions, although the sealing suffixes and bearing series may vary. Before replacing, compare the complete code, shaft size and locking type. If you have doubts, send a photo of the nameplate or the old housing: at MR Accesorios Industriales we help you identify the right equivalence without compromising equipment operation.

To request a quote, send the complete housing code on WhatsApp (for example, SSNLD 520-617 NM/MS1) or the shaft and housing measurements. With that data, the technical team at MR Accesorios Industriales will reply with the variant and sealing alternatives. We work with standard lines and special orders, always backed by more than 80 years in the Argentine industrial market.

The SKF SSNLD series split plummer block housing with solid base is a bearing mounting component that is mounted on shafts in applications requiring robust and removable support. Its two-half design makes installation and maintenance easier without having to completely disassemble the assembly. It is used in power transmission equipment, conveyors and general machinery, and MR Accesorios Industriales sells it in Buenos Aires, Argentina.

The SSNLD series designation is made up of letters that identify the type of split plummer block housing with solid base. The numbers that follow indicate the size and the combination of shaft diameter and outside diameter of the bearing it houses. For example, SSNLD 510-608 corresponds to a housing for a bearing of the 608 series with a specific shaft diameter, while SSNLD 517 refers to a particular size. Suffixes may indicate sealing or fastening variants, so it is advisable to verify the complete part number when requesting a quote.

These housings are used in industries such as food, cement, mining and materials handling, where bearings must be firmly supported and protected. In Argentina, they are common in conveyors, mills, mixers and process equipment. Their split construction allows the bearing to be replaced without dismounting the shaft, which reduces downtime. MR Accesorios Industriales offers them for different industrial applications.

To select the right housing, take into account the shaft diameter, the type and size of bearing it will house, and the environmental conditions. Sealing is key to preventing the ingress of dust or moisture; check whether the housing accepts additional seals. During mounting, ensure correct alignment between the halves and uniform tightening of the bolts. Bearing lubrication must follow the equipment manufacturer's recommendations.

SKF SSNLD series housings can be interchanged with equivalent products from other brands that follow the same standardized dimensions. However, tolerances and materials may vary between manufacturers, so it is important to confirm dimensional and functional compatibility before replacing. Do not invent part numbers: always verify the exact number in the original manufacturer's catalogue or consult a specialist.

If you need an SKF SSNLD series split plummer block housing, send us the complete part number by WhatsApp to MR Accesorios Industriales. We advise you so that you choose the correct size for your application and we will quote you as soon as possible. More than 80 years of experience back us as an industrial distributor in Buenos Aires, Argentina.

The SKF SNH split plummer block housing is a split housing that facilitates the mounting and dismounting of bearings on shafts. It is used in equipment where access is limited or quick maintenance is required. Its design allows the bearing to be installed without disassembling the shaft, which reduces downtime. MR Accesorios Industriales sells this line for industrial applications in Argentina.

The SNH designation is read as split plummer block housing of the SNH series. The numbers that follow indicate the size: for example, SNH 505 corresponds to size 5 with a 5/8" shaft diameter, while SNH 506-605 accepts two shaft diameters (1" and 5/8") depending on the bearing mounted. Suffixes may indicate sealing or fixing variants, but it is always advisable to verify the complete code with the manufacturer.

These housings are used in conveyors, mills, mixers, pumps and fans. They are common in food, cement, mining and aggregate processing plants, where dust and moisture demand robust housings. They are also used on low and medium speed transmission shafts. In Argentina, MR Accesorios Industriales supplies them to industries that need reliable spare parts for maintenance.

To select an SNH housing, take into account the shaft diameter, the type of bearing (spherical roller, ball, etc.) and the environmental conditions. Sealing is key: choose labyrinths or oil seals depending on contamination. Lubrication must be adequate and assembly requires proper alignment of the halves to avoid parasitic loads. Follow the manufacturer's instructions for tightening the bolts.

SNH housings are interchangeable between brands that follow the same dimensional standard. When looking for a replacement, compare the complete designation and the shaft and height measurements. Not all variants are equivalent: verify the type of fixing and the sealing. MR Accesorios Industriales can advise you on compatibility with other brands.

If you need an SNH split plummer block housing, send us the exact code via WhatsApp at MR Accesorios Industriales. We will quote you promptly.

The SKF SNH split plummer block housing is a housing split into two halves that facilitates bearing mounting and dismounting without dismantling the shaft. It is used to support rotating shafts in transmission equipment, with the advantage of being able to replace the bearing without moving the machine. MR Accesorios Industriales supplies this line as an official brand, with technical advice to choose the correct configuration.

The SNH designation is read as a series of split plummer block housings for bearings with cylindrical or tapered bore. The base number, for example 507, 509 or 511, indicates the housing size and the shaft diameter for which it is intended. The suffixes appearing after the slash, such as /VZ2P3, describe sealing variants, fixing type and materials. In the examples SNH 507-606/VZ2P3 or SNH 513-611/VZ2P3, the hyphen separates two equivalent numberings of the same housing. The VZ suffix usually refers to double-lip seals, and P to the presence of end plates or covers. It is always advisable to verify the exact combination in the manufacturer's catalogue.

These housings are used in conveyors, belts, elevators, mills, mixers and process equipment where the shaft must be supported with alignment and protection against dust or moisture. In Argentina they are common in food, cement, mining and aggregate processing plants, where maintenance is done with the machine stopped for the shortest possible time. The split construction allows the upper cover to be removed, the bearing extracted and reassembled without uncoupling the shaft or moving the structure. MR Accesorios Industriales supplies them for replacement and new projects.

To select the housing, you must define the shaft diameter, the bearing type (for example, ball or spherical roller) and the sealing system according to the environment. Internal clearance and lubrication must be specified: in applications with moderate load and speed, grease is used, and in humid environments or with frequent washdowns, a more closed sealing is advisable. Alignment between housings is critical to avoid parasitic loads; mounting on a rigid base and checking with a straightedge or laser is recommended. The tightness of the joining bolts also influences the final tightening.

Regarding equivalences, SKF SNH housings can be interchanged with other brands that use the same standardized designation, but not all suffixes match. The SN, SNH or SNV series from different manufacturers share main dimensions, although seals, covers and materials vary. Before replacing one housing with another of a different brand, compare the housing diameter, the center height and the fixing type. Do not invent part numbers: if you have doubts, send the complete part number of the old housing and we will verify it with the technical documentation.

To request a quote for an SNH split plummer block housing, send via WhatsApp the part number stamped on the part or the complete designation, along with the shaft diameter and the bearing type you are going to mount. At MR Accesorios Industriales we help you confirm the correct variant and resolve the mounting.

The SKF SNH split plummer block housing is a housing split into two halves that accommodates bearings with a tapered or cylindrical adapter. It is used to mount shafts in machine structures, allowing bearing replacement without disassembling the shaft. Its design facilitates installation and maintenance in equipment where access is limited. MR Accesorios Industriales carries this line with the technical backing of more than 80 years in the field.

The designation SNH identifies the series of medium-section split plummer block housings. The number that follows indicates the size: for example, SNH 218 corresponds to a housing for a bearing with a 90 mm bore, while SNH 222 is for 100 mm. The suffix TSN/H6 refers to the seal kit supplied with the housing, consisting of lip seals and flinger rings. It is important to verify that the seal kit is suitable for the working environment, since protection against dust and moisture depends on it.

These housings are used in a wide variety of industrial applications: conveyors, mills, mixers, pumps, fans and process equipment. In Argentina, they are common in the food, cement and mining industries and in aggregate processing plants. Their ability to withstand moderate radial and axial loads makes them suitable for transmission shafts and rollers. The split version allows replacing the bearing without disassembling other equipment components, which reduces downtime.

To correctly select an SNH housing, the shaft diameter, the bearing type (with tapered or cylindrical adapter), the load and the environmental conditions must be considered. The TSN/H6 seal is suitable for environments with moderate dust and moisture; for more severe conditions, other types of seals may be required. During mounting, it is essential to align the two halves of the housing and ensure uniform tightening of the bolts. Bearing lubrication must be performed according to the manufacturer's recommendations, and it is important to verify the internal clearance after mounting.

SKF SNH housings are interchangeable with those of other brands that follow the same dimension standard. When looking for a replacement, it is necessary to compare not only the shaft diameter but also the center height, the distance between holes and the seal type. MR Accesorios Industriales carries the SKF brand as part of its product line, and can advise you on the equivalence with other references. Do not invent part numbers: if you have doubts, consult us with the complete designation.

If you need an SNH split plummer block housing, write to us via WhatsApp and send us the complete part number (for example, SNH 218 TSN/H6). At MR Accesorios Industriales we help you identify the right part and resolve any technical question. With more than 80 years of experience, we are here to advise you on selection and installation.

The SKF FNL housing is a mounting component for bearings that is installed in industrial machines and equipment. Its function is to house and secure the bearing, allowing it to operate correctly and facilitating mounting and maintenance tasks. It is used in a wide variety of applications where precise support and alignment are required.

The designation FNL … A is interpreted as follows: the letters FNL identify the housing series, the symbol # represents a number that varies according to size, and the suffix A indicates a construction variant. For example, FNL 505 A, FNL 506 A and FNL 507 A correspond to different sizes within the same series. Knowing this nomenclature helps to select the right housing for each bearing.

These housings are used in industries such as food, chemical, petrochemical and process industries in Argentina. They are common in conveyors, agitators, pumps, fans and transmission equipment. Their design allows simple installation and efficient maintenance, which makes them suitable for demanding environments.

To select the correct FNL housing, take into account the type and size of the bearing, the loads and operating speeds, and the environmental conditions. It is essential to check alignment during mounting and ensure adequate lubrication. The housing seal protects against contaminants, extending the service life of the bearing.

SKF FNL housings may be interchangeable with equivalent products from other brands, provided that dimensions and load capacities are respected. When requesting a quote, it is important to provide the complete bearing and housing code to ensure compatibility. MR Accesorios Industriales supplies this brand as part of its product line.

To receive a quote for SKF FNL housings, send the exact code by WhatsApp to MR Accesorios Industriales. Our technical team will advise you so that you choose the option that best suits your equipment. With more than 80 years of experience, we provide reliable solutions for industry.

The FNL housing is a cast iron component that houses and secures bearings, generally with a split housing to facilitate mounting and maintenance. It is used in equipment requiring rigid support and precise alignment, such as conveyor belts, mills, pumps and fans. At MR Accesorios Industriales we sell the SKF line, with more than 80 years of experience in industrial distribution in Buenos Aires, Argentina.

The FNL designation is read as a series of housings with specific construction features. The number that follows, as in FNL 505 B or FNL 510 B, indicates the size and housing capacity. The B suffix indicates a design variant, usually linked to the type of sealing or the mounting method. Each full part number identifies a precise combination of dimensions and configuration, so it is essential to verify the exact part number before requesting a quote.

These housings are used in a wide variety of industries in Argentina: from food and chemical plants to steel mills and cement plants. They are common in belt conveyors, bucket elevators, mixers and continuous process equipment. Their robust design allows them to absorb combined loads and maintain shaft position under demanding conditions, reducing wear and unplanned downtime.

To select the right housing, take into account the shaft diameter, the type of bearing to be housed and the environmental conditions. Sealing is key: in dusty or humid environments, it is advisable to choose configurations with seals that protect the bearing. Lubrication must follow the manufacturer's recommendations, and alignment between housings is essential to avoid parasitic loads. Careful mounting extends the service life of the assembly.

SKF FNL housings can be interchanged with equivalent products from other brands, but mounting dimensions and load capacity may vary. Always compare drawings and technical specifications before replacing a housing. At MR Accesorios Industriales we can advise you on compatibility and available alternatives for your specific application.

If you need to request a quote for an FNL housing, send us the full part number by WhatsApp. With that data we can identify the exact part and offer you a quick response. We can also help you interpret designations or find the right replacement if the original part number is not available.

SKF LHCA series bearing housings are components designed to seat and secure bearings on shafts, making their mounting and dismounting easier in industrial applications. They are used in equipment requiring a robust and reliable support, such as conveyors, pumps, fans and machinery in general. MR Accesorios Industriales carries this line as part of its offering of power transmission and mounting components.

The designation of SKF LHCA series bearing housings is interpreted from their codes. For example, LHCA 150 / 20 and LHCA 150 / 208 indicate different variants within the same series, where the numbers may refer to the housing size and the combination with the bearing. Suffixes such as / 20 or / 208 usually indicate the shaft diameter or the type of bearing they seat. To select the correct model, it is essential to verify the dimensions of the shaft and of the bearing to be mounted.

These bearing housings are used in a wide variety of industries in Argentina, including food, chemical, petrochemical and manufacturing. They are common in conveyors, mixers, mills, centrifugal pumps and industrial fans. Their design allows secure fastening and precise bearing alignment, which helps reduce vibration and extend the service life of the assembly. MR Accesorios Industriales offers them to meet maintenance needs and new projects.

For a correct selection, it is important to consider the type of sealing required according to the working environment, the bearing internal clearance and the lubrication conditions. Mounting must be carried out ensuring proper alignment between the housing and the shaft, avoiding stresses that could damage the bearing. It is recommended to follow the manufacturer's instructions and use appropriate tools for mounting, such as pullers and hydraulic presses, for reliable operation.

Regarding equivalences and interchangeability, SKF LHCA series bearing housings can be found under similar designations from other brands, although they are not always directly interchangeable. Factors such as dimensions, tolerances and load capacity may vary between manufacturers. Therefore, when looking for a replacement, it is essential to compare the technical specifications and consult a specialist. MR Accesorios Industriales can advise you to find the best solution for your application.

If you need a quote for SKF LHCA series bearing housings or want to ask about other references, write to us by WhatsApp. Our technical team will help you identify the right model according to your equipment characteristics and operating conditions. At MR Accesorios Industriales we have more than 80 years of experience in the field, offering quality products and personalized advice.

SKF TVN A series housings are support units for bearings with cylindrical bore, designed to be mounted on shafts and to fix the bearing position in applications requiring a robust and easily aligned housing. They are used in transmission, conveying and general machinery equipment, and can support radial and axial loads depending on the bearing they house. MR Accesorios Industriales carries this line as part of its range of components for industrial maintenance.

The TVN A series designation is interpreted as follows: the letters TVN identify the housing type, and the number that follows (for example, in TVN 207 A, TVN 210 A or TVN 313 A) indicates the size and bearing housing capacity. The suffix A indicates a construction variant within the series, generally associated with the body shape or the fixing system. The examples TVN 207 A, TVN 208 A, TVN 210 A, TVN 211 A, TVN 212 A, TVN 306 A, TVN 308 A and TVN 313 A show the progression of available sizes. To select the correct one, the code must be cross-referenced with the dimensions of the bearing to be mounted.

These housings are used in industries such as food, chemical, cement and logistics, in equipment such as conveyor belts, bucket elevators, mixers, pumps and fans. In Argentina, they are common in processing plants and packaging lines, where a stable support for rotating shafts is required. Their design allows mounting bearings with cylindrical bore and fixing them by means of lock rings or nuts, as applicable. They are also used in applications where the housing must absorb small misalignments.

To choose the right housing, take into account the type of bearing it will house, the shaft diameter and the expected radial and axial loads. Check the sealing system: some housings accept seals or labyrinths to protect against dust and moisture. Lubrication must be compatible with the bearing and the service conditions. During mounting, ensure correct alignment between housings to avoid additional stresses. If the housing includes a lock ring, follow the manufacturer's instructions for tightening.

Regarding equivalents, SKF TVN A series housings can be interchanged with products from other brands that follow the same dimensional standard. It is important to compare not only the shaft diameter but also the center height and the distance between fixing holes. Other brands' codes may vary in their nomenclature, so it is advisable to consult compatibility tables. MR Accesorios Industriales can advise you on interchangeability and alternatives in its housing line.

If you need a housing for your application, send us the complete code (for example, TVN 210 A) or the bearing and shaft dimensions via WhatsApp. At MR Accesorios Industriales we help you identify the correct reference and request a quote. We can also offer alternatives if the exact model is not available. Write to us and we will reply shortly.

SKF TVN B series housings are cast components designed to house and secure bearings in applications with moderate loads. Their split design facilitates assembly and disassembly without the need to dismantle the entire shaft. They are used in transmission equipment, conveyors and general machinery, where a robust and reliable support is required. MR Accesorios Industriales supplies this line as part of its range of components for industrial maintenance.

The designation of the TVN B series is interpreted as follows: the letters TVN identify the housing type, while the number that follows indicates the size or bearing housing capacity. The final letter B indicates a construction variant, generally related to the type of sealing or locking method. For example, models TVN 207 B, TVN 208 B, TVN 306 B, TVN 311 B and TVN 313 B share the same basic design but differ in dimensions to adapt to different shaft diameters.

These housings find application in a wide variety of industries in Argentina, such as food, cement, mining and logistics. They are used in belt conveyors, bucket elevators, mixers, mills and ventilation systems. Their robust construction makes them suitable for environments with dust, moisture and variable loads. In production plants, they are usually mounted on metal structures or masonry, providing a safe support point for rotating shafts.

To correctly select a TVN B housing, it is essential to verify compatibility with the bearing it will house, the shaft diameter and the operating conditions. During assembly, ensure precise alignment between housings to avoid additional stresses on the bearings. Proper lubrication and sealing against contaminants extend the service life of the assembly. If the environment is aggressive, consider additional protections. MR Accesorios Industriales can advise you on choosing the right model for your application.

Regarding equivalences and interchangeability, SKF TVN B series housings can be replaced by products from other manufacturers that follow the same standardized dimensions. It is important to compare mounting dimensions, load capacity and locking type before replacing a housing. Not all housings with similar designations are interchangeable, so it is recommended to verify technical specifications. If you have doubts, contact us with the exact part number and we will help you find the best option.

To receive a quote for SKF TVN B series housings, send the complete product part number via WhatsApp to MR Accesorios Industriales. Our technical team will respond promptly with the information you need for your purchase.

The SONL split plummer block housing from SKF is a mounting component split into two halves that houses bearings with a tapered bore, such as those in the 222, 223 or 230 series. It is used in equipment where the bearing cannot be slid on from the end of the shaft, because it allows assembly around the shaft and the bearing already in position. MR Accesorios Industriales carries this SKF line with technical advice to choose the right size.

The SONL designation reads as a size code: the number that follows indicates the shaft diameter for which the housing is made. For example, SONL 217-517 corresponds to a 17/8 inch shaft, while SONL 230-530 is for 30/8 inches (or 3 inches). The hyphen separates the measurement in eighths of an inch, so the first number is the eighths and the second is the equivalent in inches. This nomenclature lets you quickly identify the housing you need without relying on external tables.

In Argentine industry, SONL split plummer block housings are seen in mineral conveyors, mills, mixers, centrifugal pumps and process equipment in chemical and food plants. Their advantage is that they allow the bearing to be replaced without disassembling the entire assembly: the two halves are separated, the bearing is removed and it is reassembled. That is why they are common in lines where downtime is critical, such as in the cement industry or in aggregate processing plants.

To select the housing, take into account the shaft diameter and the type of bearing you will house. The SONL is designed for bearings with a tapered bore and adapter sleeve, which facilitates mounting and adjustment of internal clearance. Check that the shaft surface is clean and free of burrs, and that the two halves of the housing close without forcing. Bearing lubrication is done through the built-in grease fitting, and it is important to align the housing well with the shaft to avoid unnecessary axial loads.

As for equivalences, SKF SONL split plummer block housings can be interchanged with similar lines from other brands, but always verify the mounting dimensions and load capacity. Not all series have the same tolerances or the same fastening system. If you need to replace an existing housing, the safest approach is to compare the complete part number and the main dimensions. At MR Accesorios Industriales we can help you with that comparison.

If you already have the part number of the housing you need, send it via WhatsApp to MR Accesorios Industriales and we'll quote you. We can also advise you if you are assembling new equipment or if you have doubts about compatibility with the bearing you will use. With more than 80 years in the business, we know the typical applications of each series and we give you a hand so you don't buy too much or too little.

The SKF SOFN BF split housing is a bearing fixing component that splits into two halves, simplifying mounting and maintenance on drive shafts. It is used in equipment where access is limited and robust support is required. MR Accesorios Industriales carries this line as an official brand, with technical advice to select the right housing for the application.

The SOFN BF designation is interpreted as follows: the letters SOFN identify the SKF split housing series, while the number that follows (224, 232, 234, 536) indicates the size and load capacity. The BF suffix indicates a variant with specific fixing and sealing characteristics. For example, the SOFN 224 BF and the SOFN 536 BF share the split design but differ in dimensions and application. Knowing these codes allows you to select the correct housing for each shaft.

These housings are used in industries such as food, cement, mining and material handling, in equipment such as conveyors, mixers, mills and pumps. In Argentina, they are common in processing plants and agricultural machinery. Their split design makes it easy to replace the bearing without completely disassembling the shaft, which reduces downtime. MR Accesorios Industriales offers them for applications that demand high strength and reliability.

To select an SOFN BF housing, take into account the shaft diameter, radial and axial load, and environmental conditions. The sealing must be chosen according to the presence of dust, moisture or chemical agents. Proper lubrication and precise alignment between the halves are key to avoiding premature wear. During mounting, verify that the support surfaces are clean and that the screws are tightened to the recommended torque.

SKF housings of the SOFN BF series are interchangeable with products from other manufacturers that follow the same standardized dimensions. However, always verify the tolerances and the fixing system before replacing one brand with another. The designation may vary between manufacturers, so it is essential to compare the critical measurements. At MR Accesorios Industriales we can guide you on compatibilities without compromising equipment performance.

If you need an SOFN BF split housing, send us the exact code on WhatsApp. At MR Accesorios Industriales we advise you so you can choose the right option for your application. Request a quote with no obligation and receive personalized technical support.

The SKF SOFN BL split housing is a bearing fixing component that mounts in two halves, making installation and maintenance easier in industrial equipment. It is used to support rotating shafts in applications where access is limited or quick mounting is required. MR Accesorios Industriales carries this line as an official brand, backed by more than 80 years in the industry.

The SOFN BL designation is interpreted in parts: SOFN identifies the split housing series with specific design characteristics, and BL indicates execution variants, such as the type of sealing or fixing. The examples SOFN 232 BL, SOFN 234 BL, SOFN 244 BL and SOFN 536 BL show how the central number changes according to size or load capacity. To select the correct one, it is essential to verify the dimensions of the shaft and the housing where it will be installed.

These housings are used in industries such as food, cement, mining and material handling, in conveyors, elevators, mills and mixers. In Argentina, they are common in processing plants and in equipment subjected to dusty or humid environments. Their split design allows the bearing to be replaced without completely disassembling the shaft, reducing downtime on critical production lines.

For a correct selection, consider the type of sealing required according to the environment (dust, water, chemicals), the internal clearance of the bearing and proper lubrication. Mounting must ensure precise alignment between the two halves; it is recommended to use the fixing screws at the specified torque and verify concentricity. Lubrication can be manual or automatic, and it is key to follow the manufacturer's instructions for each application.

Regarding equivalents, split housings from different brands can be interchanged if the critical dimensions and the bearing type match. SKF is a global reference, and in the local market there are alternatives from other manufacturers. To ensure compatibility, always compare the drawings and technical specifications. MR Accesorios Industriales can advise you on the best option for your equipment.

If you need to replace an SOFN BL housing or want to confirm the size for your application, send the complete code on WhatsApp to MR Accesorios Industriales. Our technical team helps you identify the correct part and resolve any questions about mounting or maintenance.

The SKF FSNL split plummer block housing is a component that houses and secures bearings, generally in applications where frequent mounting and dismounting is required. Its two-half design facilitates maintenance tasks, as it allows the shaft to be removed without disassembling the entire assembly. It is used in industrial rotating equipment, such as conveyors, mills and pumps, among others. MR Accesorios Industriales sells this line of SKF housings, with more than 80 years of experience in the industry.

The FSNL designation identifies SKF FSNL series split plummer block housings. The number that follows, as in FSNL 218 or FSNL 511-609, indicates the size and the bearing combination it houses. In cases with two numbers separated by a hyphen, the first refers to the housing and the second to the associated bearing. For example, FSNL 511-609 corresponds to a housing for a bearing of the 609 series. These codes allow selecting the appropriate housing according to the bearing to be mounted.

These housings are used in a wide variety of industries in Argentina, such as food, cement, mining and chemical. They are common in belt conveyors, bucket elevators, mills, mixers and centrifugal pumps. Their ability to withstand moderate radial and axial loads makes them suitable for equipment with shafts rotating at medium speeds. In addition, their robust construction resists dusty and humid environments, typical of industrial plants.

To select the correct housing, take into account the bearing you will use and the operating conditions. Verify that the housing is compatible with the shaft diameter and the bearing type (ball or roller). Sealing is key to prevent the entry of contaminants; choose the appropriate seal type according to the environment. Lubrication must be the one recommended for the bearing and the temperature and speed conditions. During mounting, ensure precise alignment between the housing and the shaft to avoid additional loads and premature wear.

SKF FSNL housings can be interchanged with equivalent products from other brands, provided the critical dimensions and load capacity match. It is essential to verify the technical specifications, such as bore diameter, center height and mounting holes. Alternatives from various manufacturers exist in the market, but interchangeability must be validated with the technical data of each application. Consult our technical team to evaluate the best option for your equipment.

If you need an FSNL split plummer block housing for your application, contact us. At MR Accesorios Industriales we advise you so that you choose the correct model. Send us the code or measurements by WhatsApp and we will quote you shortly. With more than 80 years of experience, we are your reliable partner in industrial components.

The SKF FSNL split plummer block housing is a component that houses and secures bearings, especially in applications where mounting and dismounting must be quick and simple. Its two-half design allows installing the bearing without disassembling the shaft or other components, which simplifies maintenance. MR Accesorios Industriales supplies this line as part of its range of bearing housings.

The FSNLD designation is interpreted as follows: FSNL identifies the SKF split plummer block housing series, and the final D indicates that the housing is designed for bearings with tapered bore and adapter sleeve. The number that follows, for example 520-617 or 524-620, encodes the size and dimensions of the housing, which correspond to the shaft diameter and the bearing it houses. This nomenclature allows quickly identifying the right housing for each application.

These housings are used in a wide variety of industries in Argentina, such as food, chemical, mining and cement, among others. They are common in conveyors, mills, mixers, pumps and fans, where a robust and easy-to-maintain housing is required. Their split construction facilitates inspection and bearing replacement tasks, reducing downtime.

To select the right housing, take into account the type of bearing you will mount, the shaft diameter and the operating conditions, such as load, speed and temperature. It is essential to verify shaft and housing alignment during mounting, and ensure adequate lubrication. Housing sealing is also key to protect the bearing from contaminants and extend its service life.

SKF FSNL housings can be interchangeable with equivalent products from other brands, but it is important to verify dimensions and tolerances to ensure compatibility. Do not invent codes: always consult the manufacturer or a specialist. At MR Accesorios Industriales we can advise you on the correct equivalence for your application.

If you need an FSNL split plummer block housing, write to us on WhatsApp with the product code or the features of your equipment. At MR Accesorios Industriales we help you find the right solution for your need.

El soporte bipartido SKF serie SE es un componente de fijación para rodamientos con agujero cilíndrico, diseñado para montarse sobre ejes en aplicaciones donde se requiere facilidad de instalación y desmontaje. Su construcción en dos mitades permite colocar el rodamiento sin desarmar el conjunto, lo que simplifica las tareas de mantenimiento y reduce los tiempos de parada. Es una solución robusta y versátil para una amplia gama de equipos industriales.

La designación de la serie SE se interpreta con el número que sigue, que indica el tamaño del soporte y, en algunos casos, combinaciones para diferentes diámetros de eje. Por ejemplo, SE 207 corresponde a un soporte para rodamiento con agujero de 35 mm, mientras que SE 208-307 admite dos medidas distintas, y SE 507-606 se utiliza en aplicaciones con ejes de mayor diámetro. Los sufijos pueden indicar variantes de diseño, como disposición de los agujeros de montaje o tipo de sellado, pero siempre es recomendable verificar la ficha técnica específica.

Estos soportes se emplean en una amplia variedad de industrias en Argentina, como la alimenticia, cementera, minera, papelera y de manipulación de materiales. Son comunes en transportadoras, elevadores de cangilones, mezcladoras, molinos y ventiladores industriales. Su capacidad para soportar cargas radiales y axiales moderadas los hace adecuados para equipos que operan en condiciones exigentes, siempre que se seleccione el tamaño correcto según la carga y la velocidad.

Para una selección adecuada, tené en cuenta el diámetro del eje, la carga radial y axial, y las condiciones ambientales. El montaje requiere alinear correctamente las dos mitades y asegurar los tornillos de fijación con el torque recomendado. La lubricación del rodamiento es fundamental; verificá el tipo de grasa y la frecuencia según el fabricante. Si el ambiente es polvoriento o húmedo, considerá sellos adicionales para prolongar la vida útil del conjunto.

En cuanto a equivalencias, los soportes bipartidos SKF serie SE pueden intercambiarse con productos de otras marcas que sigan la misma norma de dimensiones. Sin embargo, es importante verificar las tolerancias y el diseño exacto antes de reemplazar un componente. MR Accesorios Industriales comercializa esta línea como marca oficial, garantizando la autenticidad y el respaldo de SKF. Para una correcta sustitución, siempre compará las dimensiones críticas y consultá con nuestro equipo técnico.

Si necesitás reemplazar un soporte bipartido, mandanos el código completo por WhatsApp. En MR Accesorios Industriales te asesoramos para que elijas la opción correcta según tu aplicación. Con más de 80 años de experiencia, somos tu socio confiable en componentes industriales.

El soporte bipartido SKF serie SE es un componente de fijación para rodamientos que se divide en dos mitades, lo que permite montarlo o reemplazarlo sin desarmar el eje ni la transmisión. Se usa en equipos donde el acceso es limitado y el tiempo de parada debe ser mínimo. MR Accesorios Industriales comercializa esta línea como marca oficial, con el respaldo de más de 80 años en el rubro industrial.

La designación de los soportes bipartidos SKF serie SE se interpreta así: SE indica que es un soporte bipartido de la serie SE; el primer número de tres cifras corresponde al diámetro del eje para el que está previsto, y el segundo número, cuando aparece separado por un guion, señala una variante de tamaño o diseño. El sufijo K seguido de un dígito hace referencia al tipo de fijación o al sistema de bloqueo del rodamiento. Por ejemplo, SE 509 K7 es un soporte para eje de 45 mm con fijación K7; SE 511-609 K7 y SE 512-610 K7 son variantes con dos medidas asociadas, típicas de montajes con rodamientos de distinta sección. Verificá siempre el código completo en el plano o en la chapa del equipo.

Estos soportes se emplean en una amplia variedad de industrias en Argentina: plantas de alimentos y bebidas, cementeras, siderúrgicas, papeleras, minería, tratamiento de áridos y transporte de materiales. Son comunes en transportadores de banda, elevadores de cangilones, mezcladoras, molinos, bombas centrífugas de gran porte y ventiladores industriales. Su diseño bipartido facilita el mantenimiento en equipos donde el rodamiento está montado en un eje largo o en una posición de difícil acceso, ya que permite retirar la tapa superior sin mover el conjunto. También se usan en aplicaciones donde el soporte debe absorber cargas combinadas y cierto desalineamiento.

Para seleccionar correctamente un soporte bipartido SE, tené en cuenta el diámetro del eje, el tipo de rodamiento que va alojar, la carga radial y axial, y las condiciones ambientales. El sellado es clave: en ambientes con polvo, humedad o lavados frecuentes, conviene elegir laberintos o retenes adecuados. La lubricación debe ser compatible con el rodamiento y renovarse según el plan de mantenimiento. Durante el montaje, asegurá una alineación precisa entre las dos mitades y un apriete uniforme de los tornillos para evitar deformaciones. El juego interno del rodamiento no debe modificarse al cerrar el soporte.

En cuanto a equivalencias e intercambiabilidad, los soportes bipartidos SKF serie SE pueden reemplazar a otros de similar construcción y medidas, pero no hay una tabla universal: cada fabricante define sus propios diámetros, alturas de centro y sistemas de fijación. Por eso, antes de sustituir un soporte, compará las dimensiones críticas —diámetro de eje, distancia entre tornillos, altura al centro— y el tipo de rodamiento admitido. MR Accesorios Industriales puede ayudarte a encontrar la referencia equivalente dentro de su línea de soportes, sin comprometer el funcionamiento del equipo.

Si necesitás un soporte bipartido SKF serie SE, envianos el código completo por WhatsApp a MR Accesorios Industriales. Con los datos del equipo y una foto de la pieza, te asesoramos para que elijas la opción correcta y coordines la cotización. Nuestro equipo técnico cuenta con más de 80 años de experiencia en el rubro y está para ayudarte a mantener la producción en marcha.

The SKF SE split housing is a bearing mounting component that is assembled in two halves, simplifying installation and maintenance in equipment where access is limited. It is used to support rotating shafts in a wide variety of industrial machines. MR Accesorios Industriales supplies this line as part of its range of bearing housings and accessories, with technical advice to choose the right configuration.

The SE series designation is interpreted by the number following the letters, which indicates the housing size and the shaft diameter for which it is intended. The VU suffix, when present, indicates a specific construction variant, often linked to the type of sealing or the shape of the groove. For example, the code SE 508-607/VU801 combines a base size with a particular configuration. Knowing these elements helps identify the correct replacement.

These housings are used in conveyors, mills, mixers, pumps, fans and transmission systems in food, cement, mining and aggregate processing plants. Their split design allows the bearing to be replaced without dismantling the shaft or the structure, reducing downtime. In Argentina, they are common in continuous process equipment where accessibility is difficult.

To select the housing, verify that the shaft diameter and the bearing series match the designation. During assembly, ensure correct alignment between the two halves and tighten the bolts evenly. Lubrication must be compatible with the housed bearing, and sealing suitable for the environment: consistent grease for wet or dusty areas. Check axial and radial clearance according to the equipment tolerances.

Split housings from different brands can be interchanged if the main dimensions, load capacity and mounting type match. However, tolerances and materials may vary, so it is advisable to confirm equivalence with a specialist. MR Accesorios Industriales can guide you on alternatives in the market, without compromising the performance of the assembly.

If you need an SE split housing, send us the complete code via WhatsApp. At MR Accesorios Industriales we help you identify the exact part and resolve your technical doubts. Request a quote with no obligation and ensure the operation of your equipment.

The SKF SD split housing is a bearing mounting component that is mounted on shafts and supports radial load in rotating equipment. Its two-piece design facilitates assembly and disassembly without completely dismantling the shaft, which simplifies maintenance. It is used in applications requiring robustness and precise alignment, such as conveyors, mills and industrial machines. MR Accesorios Industriales sells this line as an official brand.

The designation of SD housings combines letters and numbers that indicate size and configuration. For example, SD 16X24X3 indicates metric dimensions: 16 mm bore diameter, 24 mm outer diameter and 3 mm width. In contrast, SD 3138 and SD 3140 correspond to series with inch measurements or internal codes. Suffixes may indicate sealing or mounting variants, but it is always advisable to verify the complete part number with our technical team to ensure compatibility.

These housings are used in industries such as food, cement, mining and materials handling. In Argentina, they are common in grain conveyors, flour mills, aggregate processing plants and process equipment. Their split construction allows the bearing to be replaced without dismantling the shaft, reducing downtime. They are also used in industrial fans and large centrifugal pumps, where alignment and resistance to combined loads are critical.

To select the appropriate housing, take into account the shaft diameter, radial and axial load, and environmental conditions. Sealing is key: in dusty or humid environments, choose versions with additional seals. Lubrication must be compatible with the bearing and operating temperatures. During assembly, ensure correct alignment between the halves and uniform tightening of the bolts to avoid deformation. Cleaning the contact surfaces prevents premature failures.

Regarding equivalences, SKF SD housings can be interchanged with products from other brands that follow the same dimensional standard. However, not all part numbers are directly replaceable: always verify the critical dimensions and the mounting type. MR Accesorios Industriales sells the SKF brand as part of its housing line, and also offers in-house manufacturing alternatives for specific needs. Ask us about interchangeability before replacing a component.

If you already have the part number of the housing you need, send it by WhatsApp to MR Accesorios Industriales and we will quote it. We can also advise you if you are not sure of the correct designation: with the equipment data and shaft measurements, we help you identify the part. More than 80 years of experience in industrial distribution back us to offer you the right solution.

The SKF SD split plummer block housing is a bearing mounting component, designed to be mounted on shafts and to simplify maintenance. Its two-piece construction allows the bearing to be installed or replaced without dismantling the entire equipment, which reduces downtime. It is used in industrial applications where robustness and precise alignment are required. MR Accesorios Industriales carries this line as part of its range of bearing housings.

The designation of SKF SD split plummer block housings is interpreted from the series and a number that indicates the size. For example, SDAF 240-26, SDAF 336, SDAF 540 and SDAF 3280 show how the code varies according to the housing dimensions. The SDAF prefix identifies the series, while the following number defines the combination of dimensions and the bearing it houses. This nomenclature allows selecting the right housing for each shaft and bearing type.

These housings are used in a wide variety of industries in Argentina, such as food, cement, mining, petrochemical and material handling. They are common in conveyors, mills, mixers, pumps and industrial fans. Their split design simplifies mounting on drive shafts and allows compensating for slight misalignments. In addition, their robust construction makes them suitable for environments with dust, humidity or moderate loads.

To select an SD split plummer block housing, take into account the shaft diameter, the type and size of bearing it will house, and the operating conditions. It is essential to verify the alignment between housings and the shaft to avoid parasitic loads. The sealing must be chosen according to the environment: labyrinth for dirty environments or oil seals for greater tightness. Proper lubrication and careful mounting extend the service life of the assembly. Always consult the manufacturer's technical specifications.

SKF SD split plummer block housings may be interchangeable with those of other brands that follow the same mounting standard, such as the SNL or SAF series. However, it is important to verify the critical dimensions and load capacity before replacing one housing with another. Interchangeability is not always direct and may require adaptations. MR Accesorios Industriales can advise you on the equivalents available in its catalogue.

If you need an SD split plummer block housing for your application, contact us on WhatsApp. At MR Accesorios Industriales we help you identify the correct model according to your bearing and shaft, and we provide a no-obligation quote. With more than 80 years of experience, we are your reliable partner in power transmission.

The SN split plummer block housing is a split housing used to mount bearings on shafts in industrial equipment. It opens into two halves, which makes mounting and dismounting easier without dismantling the shaft or the transmission. SKF is an official brand that MR carries, and this line covers a variety of sizes for different applications. If you need to replace a housing or assemble new equipment, send us the part number by WhatsApp and we will quote you.

The SN designation is read as a series of split plummer block housings. The number that follows indicates the size: for example, SN 3026, SN 3030, SN 3034, SN 3036, SN 3038, SN 3040, SN 3044 and SN 3048. The higher the number, the greater the housing capacity. Any suffixes that may appear after the number indicate sealing, fastening or material variants, but they are not detailed in this record. To choose the right one, always start from the complete part number and check with us if you have any doubts.

These housings are used in conveyors, mills, mixers, pumps, fans and machinery in general. In Argentina, they are common in food, cement, mining and petrochemical plants. They allow mounting deep groove ball bearings or spherical roller bearings, and their split design simplifies maintenance in hard-to-reach places. MR Accesorios Industriales carries this line for replacement and new projects.

To select the housing, take into account the shaft diameter, the bearing type and the loads. Sealing is key: choose labyrinth seals or oil seals depending on the environment. Lubrication must be adequate and mounting requires proper alignment of the halves to avoid stress. Follow the manufacturer's instructions and check the axial clearance. If you need advice, contact us.

SN housings from different brands can be interchanged if dimensions and capacities match. Do not invent equivalences: always verify with the original part number. At MR we carry SKF as an official brand, and we can guide you on alternatives. Interchangeability depends on tolerances and fastenings, so check before replacing.

If you already have the part number of the housing you need, send it by WhatsApp to MR Accesorios Industriales and we will quote you. We can also help you identify the model if you send us the shaft dimensions and a photo. We are in Buenos Aires, Argentina, and have been supplying industrial solutions for more than 80 years.