DODGE F2B-SCEZ-010L-SH flange bearing 2 holes
- Brand
- DODGE
- Category
- Bearing housings
- Subcategory
- Y-bearing unit
- Series
- SCEZ
We respond promptly.
Since 1945 · Martínez, Buenos Aires, Argentina
Request your quote via WhatsApp or email, with the quantity you need.
Can't find the exact model? Write to us with the part number or model you're looking for: we'll find it and quote it, even if it's not listed in the catalog.
Description
DODGE F2B-SCEZ-010L-SH is a reference of flange bearing 2 holes, within Bearing housings. Request a quote for F2B-SCEZ-010L-SH via WhatsApp or email with the quantity you need; we respond promptly with the quote and equivalents.
The Y-bearing with 2-bolt flange insert is a mounted unit that combines a cast iron housing with a self-aligning ball bearing already installed. It is fastened with two bolts to the structure and supports the rotating shaft, absorbing misalignments typical of assembly. In the DODGE SCEZ series, MR Accesorios Industriales supplies these units for equipment that needs simple, robust support with quick replacement.
The SCEZ series designation is read in blocks. The F2B prefix indicates the 2-bolt flange housing; SCEZ identifies the insert family and its sealing system; the three-digit number that follows, as in F2B-SCEZ-008L-SH or F2B-SCEZ-010L-SH, corresponds to the shaft diameter for which the unit is assembled. The L suffix indicates the insert locking type on the shaft and SH refers to the sealing configuration. With this data the part is identified without ambiguity.
These housings are used in material handling, belts, elevators, mixers, blowers and process lines where the shaft rotates at moderate speeds and the load is mainly radial. In food, chemical, cement and aggregate processing plants in Argentina they are common due to the ease of replacing the insert without disassembling the structure. They also appear in pumping and ventilation equipment where alignment is difficult to guarantee.
To select correctly, consider the shaft diameter, radial load and direction of force on the flange. The self-aligning insert tolerates small angular deviations, but the housing should be supported on a flat surface and the two bolts tightened evenly. The SH seal protects against dust and splashes; in environments with water or fine particles, check the condition of the lips and renew lubrication according to the duty cycle.
Between brands, 2-bolt flange mounted units are interchanged by shaft dimensions, housing type and sealing configuration, not by the commercial code. The same diameter may vary in center height, hole spacing and locking system. If you need to replace an existing unit, send us the complete code or the housing dimensions and we will indicate the compatible alternative from the DODGE line.
If you have the code F2B-SCEZ-008L-SH, F2B-SCEZ-010L-SH or any other reference from the SCEZ series, send it via WhatsApp to MR Accesorios Industriales and we will quote it promptly. We can also advise you on the insert, seal or housing that best suits your equipment.
Dimensions
- Bore
- 5/8 in
Frequently Asked Questions
- What does the SH suffix mean in the SCEZ series?
- The SH suffix identifies the sealing configuration of the insert within the mounted unit. It is the data that defines protection against dust and splashes, and it should be respected when requesting a replacement to avoid losing performance in demanding environments.
- How do I choose the correct shaft diameter?
- The three-digit number in the designation, as in F2B-SCEZ-008L-SH, indicates the shaft diameter. Measure the shaft with a caliper at the support area and compare with that code. If in doubt, send us the measurement and we will indicate the corresponding unit.
- Can only the insert be replaced without changing the housing?
- Yes. These units allow renewing the insert bearing while keeping the flange housing mounted on the structure, provided the shaft diameter and locking system match. This is an advantage for reducing maintenance downtime.