SKF Bushings and sleeves

The SKF PTB friction bushings are cylindrical components mounted between a shaft and a housing to reduce friction and wear. They work as self-lubricating or lubricated bushings, supporting radial loads in rotating or oscillating movements. They are used in industrial and automotive machinery and equipment where a compact solution with simple maintenance is required. MR Accesorios Industriales sells this line as part of its range of transmission and support components.

The PTB series designation is interpreted as follows: PTB indicates the type of friction bushing; the first number after the hyphen corresponds to the inside diameter (d), the second to the outside diameter (D) and the third to the length (B), all in millimeters. The suffixes J and S refer to design characteristics, such as the material type and the design of lubrication grooves or channels. For example, PTB-12X22X8-J1S has a 12 mm inside diameter, 22 mm outside diameter and 8 mm length. This nomenclature makes it possible to quickly identify the main dimensions and select the right bushing for each application.

These bushings are used in a wide variety of industries in Argentina, such as automotive, metalworking, food and agricultural. They are found in pumps, compressors, conveyor belts, machine tools, bottling equipment and lifting systems. Their function is to support radial loads and allow relative movement between parts, reducing wear and noise. They are an economical and reliable alternative to bearings in low-speed, moderate-load applications, especially where space is limited.

To correctly select a PTB bushing, take into account the radial load, sliding speed and environmental conditions. Check that the inside diameter matches the shaft and the outside diameter matches the housing, respecting the recommended tolerances. Lubrication is key: some models incorporate channels that facilitate lubricant distribution. During installation, ensure precise alignment to avoid irregular wear. If the bushing works in dirty environments, consider additional protections. Careful installation extends the service life of the component.

Regarding equivalents and interchangeability, SKF PTB series friction bushings can be replaced by products from other manufacturers that follow the same dimensional designation (inside diameter, outside diameter and length). However, it is essential to verify the material, lubrication type and tolerances, as they can vary between brands. Do not invent codes: always compare technical specifications. If you have doubts, consult our technical team to ensure compatibility.

To request a quote for the bushing you need, send the full code by WhatsApp to MR Accesorios Industriales. Our team will advise you and send your quote as soon as possible. We work with leading brands and offer solutions for your industrial requirements.

SKF PCM E series friction bushings are thin-walled bushings with a sliding coating, designed to withstand radial loads in oscillating or limited-rotation movements. They are used in joints, pivots and guides where low friction and minimal maintenance are required. MR Accesorios Industriales offers this line as part of its range of power transmission and motion components.

The PCM designation identifies SKF friction bushings with a steel backing and sliding layer. The numbers that follow indicate dimensions in millimeters: the first two digits correspond to the inner diameter, the next two to the outer diameter, and the last two to the width. For example, PCM 050705 E has a 5 mm inner diameter, 7 mm outer diameter and 5 mm width. The E suffix indicates a variant with specific sliding layer characteristics, such as greater wear resistance or better performance under load conditions. The examples PCM 050708 E and PCM 060806 E show how dimensions vary according to the application.

These bushings are used in a wide variety of industries in Argentina: from agricultural machines and road equipment to packaging lines, forklifts and lifting systems. They are common in hydraulic cylinder joints, crane arms, wheel axles and steering mechanisms. Their compact design makes it possible to replace bronze bushings or bearings in tight spaces, with the advantage of not requiring additional lubrication in many applications. They are also used in material handling equipment and in the food industry, where cleanliness is critical.

To select the right bushing, take into account the radial load, sliding speed and type of movement (oscillating or rotating). The PCM E series is intended for moderate loads and operating temperatures within a standard range. During assembly, ensure correct alignment between the shaft and the housing; excessive misalignment accelerates wear. Sealing the assembly is key to preventing the entry of contaminants. If movement is continuous, verify that lubrication is adequate according to the manufacturer. Cleaning the contact surfaces before installation extends service life.

Regarding equivalents, SKF PCM E friction bushings can be interchanged with products from other manufacturers that follow the same dimensional designation and sliding layer type. However, not all thin-walled bushings are equal: always verify tolerances and the sliding layer material before replacing. MR Accesorios Industriales carries the SKF brand as part of its component line, and can advise you on compatibility with other brands it distributes. Do not invent codes: if you have doubts, ask us with the exact measurement.

If you need to replace a friction bushing, send us the complete code via WhatsApp to MR Accesorios Industriales. With the designation PCM 050705 E or the one shown on your equipment, we can identify the part and quote it. We can also help you select the correct variant for your application. Write to us and we will reply shortly.

SKF PCM M series plain bearings are thin-walled self-lubricating bushings that combine a steel backing with a sintered bronze layer and a PTFE and lead mixture. They are used to support radial loads in oscillating, rotating or sliding movements, where continuous lubricant supply is not possible or not advisable. Their compact design allows them to be mounted in confined spaces and to replace solid bushings with lower load capacity.

The designation PCM identifies SKF plain bearings with a metal backing and sliding layer. The numbers that follow indicate the basic dimensions: in PCM 081012 M, for example, the first two digits correspond to the inside diameter, the next two to the outside diameter and the last two to the width, all in millimeters. The suffix M indicates the standard version with PTFE and lead layer. Other examples such as PCM 101215 M or PCM 121420 M follow the same logic: each pair of digits defines a dimension. Always verify the complete code to ensure the correct size.

These plain bearings are used in a wide variety of industrial equipment in Argentina: presses, machine tools, hydraulic and pneumatic cylinders, cranes, elevators, material handling equipment and agricultural machinery. They also appear in automotive and heavy transport applications where wear resistance and low friction without frequent maintenance are required. Their ability to work under radial load conditions and reciprocating movements makes them suitable for joints, pins and shafts that rotate at moderate speeds.

To select the correct plain bearing, take into account the radial load, sliding speed and operating temperature. The PCM M series withstands relatively high loads compared with plastic bushings, but it is not intended for high speeds or continuous rotation at high speed. Mounting must be carried out with the shaft and housing clean and free of burrs; a slight interference fit in the housing and adequate diametral clearance on the shaft are recommended. Initial lubrication is not necessary, although in highly contaminated environments the assembly can be sealed to extend service life.

Regarding equivalents, plain bearings with steel backing and PTFE layer are known under different names depending on the manufacturer. There is no universal nomenclature, so interchangeability requires comparing dimensions, tolerances and load capacity. SKF is an official brand that MR carries, and its products maintain recognized quality standards. If you need to replace an existing bushing, the safest approach is to start from the actual housing and shaft measurements and compare them with the manufacturer's table.

MR Accesorios Industriales carries the SKF PCM M plain bearing line and can advise you on selection according to your application. If you already have the bushing code or the shaft and housing measurements, send us the data via WhatsApp and we will provide a quote promptly. With more than 80 years in the market, MR Accesorios Industriales is a reliable partner for your industrial component needs.

The SKF KM series lock nut is an essential component for mounting and securing bearings on shafts. Its design allows precise and secure adjustment, facilitating the installation and maintenance of transmission systems. Manufactured with high-quality materials, it guarantees durability and resistance in demanding industrial applications. It is compatible with a wide range of bearings and is used together with lock washers to secure the bearing position on the shaft.

The designation of the KM series is interpreted as follows: the prefix KM indicates that it is a lock nut with slots for a hook wrench, and the number that follows (for example, KM 0, KM 1, KM 2) corresponds to the specific size and thread. The higher the number, the larger the thread diameter and load capacity. This nomenclature allows quick identification of the right nut for each application, facilitating selection and replacement.

These nuts are used in a wide variety of industries in Argentina, such as metallurgy, food, mining and petrochemical. They are common in power transmission equipment, such as gearboxes, pumps, fans and conveyors, where bearings must be secured on rotating shafts. Their presence is key to maintaining the structural integrity and correct operation of machinery, preventing axial displacement and unwanted vibrations.

For proper selection, it is essential to consider the diameter and thread pitch of the shaft, as well as the type of bearing to be secured. Mounting must be done with the corresponding lock washer (MB series) to prevent loosening. It is recommended to apply the tightening torque specified by the manufacturer and verify the alignment of the assembly. Lubrication of the thread facilitates mounting and dismounting, and the use of suitable tools, such as hook wrenches, prevents damage to the slots.

Regarding equivalences and interchangeability, SKF KM series lock nuts are compatible with those of other manufacturers that follow the same dimension standard. However, it is important to verify the technical specifications and material quality, as they may vary between brands. Always consult a specialist before mixing components from different origins to ensure optimal and safe performance.

If you need SKF KM series lock nuts, at MR Accesorios Industriales we advise you so you choose the correct size. Send us the code via WhatsApp and we will quote you promptly. With more than 80 years of experience, we guarantee personalized attention and quality products for your industrial projects.

The SKF KMT series lock nut is a precision component used to secure bearings with tapered bore to shafts, providing safe retention and exact fit. Its design allows for simple mounting and dismounting, facilitating the maintenance of rotating equipment. It is ideal for applications requiring reliable and repeatable fastening.

The designation KMT followed by a number indicates the size and characteristics of the lock nut. For example, KMT 0, KMT 1, KMT 2, etc., where the number relates to the shaft diameter and thread. Suffixes may indicate variations in thread pitch or design, but they always refer to the standard SKF lock nut series. This nomenclature allows quick identification of the appropriate part for each application.

These lock nuts are used in a wide variety of industries in Argentina, such as food, metallurgy, petrochemical and mining. They are common in pumps, fans, conveyor belts and machine tools, where bearings must be mounted with controlled interference. Their use facilitates axial and radial adjustment, ensuring bearing service life and reducing vibration.

To select the correct lock nut, it is essential to consider the shaft diameter, thread type and locking method. Mounting requires clean surfaces, adequate lubrication and application of the recommended tightening torque. Alignment with the bearing and the use of appropriate tools, such as hook spanners, are key to avoiding damage. Careful mounting extends the life of the assembly.

Regarding equivalences, SKF KMT lock nuts can be interchanged with products from other brands that follow the same dimensional and thread standard. However, it is important to verify technical specifications and material quality, as not all brands offer the same performance. MR Accesorios Industriales sells the SKF brand.

To request a quote for the SKF KMT series lock nut you need, simply send the part number via WhatsApp to MR Accesorios Industriales. Our technical team will advise you to choose the correct option for your application. With more than 80 years of experience, at MR we provide reliable solutions for bearing mounting.

SKF N series lock nuts are the inch version of the well-known KM nuts: they secure a bearing on its adapter sleeve or at the shaft end, and are locked with a W series lock washer of the same number. They are used in machines and housings of North American origin, where the shaft and adapter sleeve come in inch sizes.

The nut number indicates the thread size, and it pairs with the washer: an N 10 is locked with a W 10. The nut tightens the bearing against the tapered adapter sleeve or against the shaft shoulder, and the lock washer prevents it from loosening with vibration: one of its tabs is bent into one of the nut slots.

To mount it, use a hook spanner of the correct size, never a punch and hammer, which damage the slots and leave the nut unable to be retightened. In adapter sleeve mounts, the tightening defines the final internal clearance of the bearing, so it is advisable to follow the tightening angle indicated by the bearing manufacturer.

When replacing a bearing, it is recommended to also replace the lock washer: a tab that has already been bent once loses strength. The nut can be reused if the thread and slots are in good condition.

To request a quote, send us the complete nut designation via WhatsApp, or that of the adapter sleeve or bearing it will secure, and we will tell you which nut and which washer correspond.

The adapter sleeve is a tapered element that makes it possible to mount a bearing with a tapered bore — such as series 22 spherical roller bearings or Y-type needle roller bearings — on a plain shaft, without the shaft needing a machined shoulder or a keyway.

The SKF H series is identified by the size number, which corresponds to the size of the bearing and the shaft it is mounted on. It is tightened with a KM series lock nut and an MB series lock washer, which must be ordered together with the sleeve if you do not have them.

It is used in conveyors, fans, pumps and long shafts where machining a shoulder is not advisable, because the sleeve is mounted by sliding along the plain shaft to its final position, instead of butting against a fixed shoulder.

Tightening the nut on the tapered sleeve must be done following the manufacturer's procedure, generally by controlling how much the bearing's internal clearance is reduced as it is tightened: insufficient tightening leaves the bearing loose on the shaft, and excessive tightening removes the internal clearance and makes it fail from overload.

Metric adapter sleeves are fairly standardized by size among bearing manufacturers, so an SKF H series sleeve usually has an equivalent of the same size from other brands.

Tell us the shaft diameter or the bearing number you are going to mount and we will confirm the corresponding sleeve, nut and washer. MR Accesorios Industriales gives quotes by WhatsApp or email.

The SKF HA series adapter sleeve is a mounting component that secures bearings with a tapered bore onto cylindrical shafts. It consists of a split sleeve, a lock nut and a lock washer, and is used to position and secure the bearing in applications requiring precise fit and easy disassembly. It is a common solution in power transmission equipment, gearboxes and industrial machinery.

The HA series designation is read as HA followed by a four-digit number. The first two digits indicate the shaft diameter in inches and the last two the bearing bore diameter in millimeters. For example, HA 2309 corresponds to a 2 3/16" shaft and a 45 mm bore bearing; HA 2311 to a 2 11/16" shaft and 50 mm bearing; HA 2313 to 2 15/16" and 60 mm; HA 2315 to 3 3/16" and 65 mm; HA 2316 to 3 1/4" and 70 mm; HA 2317 to 3 5/16" and 75 mm; HA 2320 to 3 3/4" and 90 mm; and HA 2326 to 4 7/16" and 115 mm. This nomenclature makes it easy to identify the shaft-bearing combination.

SKF HA series adapter sleeves are used in a wide variety of industries in Argentina, such as food, chemical, mining and cement. They are common in gearboxes, conveyors, mills, mixers and industrial fans. They allow mounting bearings with a tapered bore onto cylindrical shafts, which simplifies design and maintenance. They are also used in equipment where the axial position of the bearing needs to be adjusted or frequent disassembly is required without damaging the shaft.

To correctly select an HA adapter sleeve, verify that the shaft diameter matches the one indicated in the designation and that the bearing bore is the corresponding one. During mounting, clean the surfaces and apply a thin layer of oil. Insert the sleeve into the bearing and thread the nut with the lock washer. Tighten the nut with the appropriate wrench until the recommended internal clearance is obtained. It is essential to align the assembly to avoid additional loads and ensure a long service life.

Regarding equivalences, SKF HA series adapter sleeves are interchangeable with those of other brands that follow the same designation. However, always verify tolerances and surface treatment, as they may vary between manufacturers. Interchangeability facilitates replacement, but it is the user's responsibility to confirm that dimensions and load capacity are compatible with the application. Do not invent part numbers: consult MR if you have doubts about the equivalence of a specific product.

To request a quote for the SKF HA series adapter sleeve you need, send the complete part number via WhatsApp to MR Accesorios Industriales. Our technical team advises you to choose the correct size. With more than 80 years of experience, at MR Accesorios Industriales we sell official brands and manufacture housings and chains. Write to us and we will respond promptly.

El manguito de fijación SKF serie HE es un componente clave para montar rodamientos con agujero cónico sobre ejes cilíndricos. Se compone de un manguito con rosca exterior y una tuerca con arandela de seguridad que, al ajustarse, genera la interferencia necesaria para fijar el rodamiento. Se usa en equipos rotativos donde se requiere una unión firme y desmontable, como reductores, bombas, ventiladores y transportadoras.

La designación de la serie HE se lee como HE seguido de un número de cuatro cifras. Las dos primeras cifras indican el tipo de rodamiento al que está destinado: por ejemplo, HE 23 corresponde a rodamientos de la serie 23, y HE 31 a la serie 31. Las dos últimas cifras se relacionan con el diámetro del eje: a mayor número, mayor diámetro. Así, un HE 2306 se usa con rodamientos de la serie 23 para un eje de menor diámetro que un HE 2328, que es para un eje más grande. Los sufijos pueden indicar variantes en el paso de rosca o en el diseño de la tuerca, pero siempre conviene verificar el código completo.

Estos manguitos se emplean en una amplia variedad de industrias en Argentina: alimenticia, química, petroquímica, cementera, siderúrgica y de tratamiento de áridos, entre otras. Son comunes en equipos como cintas transportadoras, molinos, mezcladoras, bombas centrífugas, ventiladores industriales y máquinas herramienta. Su función es permitir el montaje de rodamientos con agujero cónico en ejes cilíndricos, facilitando el ajuste y el desmontaje sin dañar el eje ni el rodamiento. También se usan en aplicaciones donde se requiere una fijación axial precisa y una buena concentricidad.

Para seleccionar el manguito correcto, tené en cuenta el diámetro del eje, la serie del rodamiento y el tipo de rosca. Es fundamental que el manguito corresponda exactamente al rodamiento que vas a montar, ya que de ello depende la interferencia y el juego interno. Durante el montaje, limpiá bien el eje y el agujero del rodamiento, aplicá una capa fina de lubricante y ajustá la tuerca con la llave adecuada hasta lograr el juego radial recomendado. La arandela de seguridad evita que la tuerca se afloje. Verificá la alineación y el apriete según las especificaciones del fabricante.

En cuanto a equivalencias, los manguitos SKF serie HE son intercambiables con los de otras marcas que siguen la misma designación normalizada, como FAG, NSK o NTN, siempre que coincidan el código y las dimensiones. Sin embargo, no todos los fabricantes usan exactamente la misma nomenclatura, por lo que es imprescindible comparar las medidas y la rosca antes de reemplazar. Si tenés dudas, consultanos con el código original y te asesoramos sin compromiso.

Para cotizar el manguito de fijación SKF serie HE que necesitás, mandanos el código completo por WhatsApp a MR Accesorios Industriales. Contamos con más de 80 años de experiencia en el rubro y te ayudamos a identificar la pieza correcta para tu aplicación. Escribinos y te respondemos a la brevedad.

The SKF withdrawal sleeve of the AH series is a key part for removing bearings with a tapered bore without damaging the shaft or the bearing. It is used in industrial maintenance tasks where clean and safe disassembly is a priority. MR Accesorios Industriales carries this line as an official brand, backed by more than 80 years in the industry.

The designation of SKF AH series sleeves is read systematically: the prefix AH indicates a withdrawal sleeve, and the number that follows identifies the size and the thread. For example, AH 309 corresponds to a sleeve for bearings of the 309 series, while AH 2240 and AH 2340 are linked to bearings of the 2240 and 2340 series. The suffixes, when they appear, indicate thread or dimension variants; in the examples AH 3032 and AH 3034 the number refers to the associated bearing. Knowing this logic allows you to choose the correct sleeve from the bearing part number.

These sleeves are used in industries such as food, cement, mining, steel and pulp and paper, where tapered roller bearings mounted on tapered shafts require frequent removal. They are also common in maintenance workshops and in rotating equipment such as pumps, fans, conveyor belts and gearboxes. In Argentina, MR Accesorios Industriales supplies them to plants that need to reduce downtime and ensure disassembly without impacts or excessive heating.

To select the right sleeve, verify that the number matches the bearing to be removed and that the thread is compatible with the withdrawal nut. During mounting, apply the recommended lubrication to the thread and the tapered surface to facilitate turning and prevent seizing. The alignment of the assembly is essential: a poorly centered sleeve can damage the seat. Follow the manufacturer's instructions for torque and the removal method, and check the condition of the thread before each use.

As for equivalences, other manufacturers offer sleeves with similar designations, but they are not always interchangeable. The thread, length and tapered diameter can vary between brands. Therefore, before replacing an SKF sleeve with one from another company, compare the critical dimensions and consult a specialist. At MR Accesorios Industriales we can guide you on compatibility, without inventing part numbers or promising what has not been verified.

If you need an SKF AH series withdrawal sleeve, send us the exact bearing or sleeve part number on WhatsApp. At MR Accesorios Industriales we quote you and advise you so that the removal is safe and efficient. Let's not improvise with parts that do not correspond: the integrity of the shaft and the bearing is at stake.

The SKF AHX series withdrawal sleeve is a component used to facilitate the dismounting of bearings mounted on adapter sleeves. It is placed between the bearing and the lock nut, and when the nut is turned, the sleeve pushes the bearing out of its seat in a controlled manner. It is a key part for industrial maintenance, as it allows bearings to be removed without damaging them or the shaft.

The designation of the AHX series is interpreted as follows: the prefix AHX indicates that it is a withdrawal sleeve. The numbers that follow correspond to the size of the bearing or adapter sleeve with which it works. For example, AHX 310 is used with bearings of the 310 series, while AHX 2310 is used with bearings of the 2310 series. In some cases, suffixes may appear indicating design variants, such as a different length or a surface treatment, but it is always advisable to verify compatibility with the corresponding bearing and adapter sleeve.

These sleeves are used in a wide variety of industries in Argentina, such as metallurgy, cement, mining, food and petrochemical. They are common in equipment with bearings mounted on adapter sleeves, such as conveyors, mills, pumps, fans and gearboxes. In plants where predictive maintenance and reduction of downtime are critical, the use of withdrawal sleeves speeds up replacement tasks and prevents damage to components.

To select the appropriate sleeve, it is essential to identify the bearing and the adapter sleeve being used. The withdrawal sleeve must be compatible in diameter and thread with the lock nut. During assembly, it is recommended to lubricate the thread and the contact surface to facilitate sliding and prevent seizing. It is important to follow the manufacturer's instructions regarding tightening torque and assembly sequence. Correct alignment and thorough cleaning of surfaces prevent premature damage.

Regarding equivalences and interchangeability, withdrawal sleeves from different brands can be interchangeable if dimensions and thread match. However, not all manufacturers use the same designation. Therefore, it is always advisable to verify the actual measurements and consult a specialist before replacing a part. At MR Accesorios Industriales we supply the SKF brand, but we can advise you on compatibility with other brands.

If you need a quote for an SKF AHX series withdrawal sleeve, write to us on WhatsApp with the exact part number on your bearing or adapter sleeve. At MR Accesorios Industriales we help you identify the correct part and resolve your technical doubts. More than 80 years of experience back us.

The SKF AOH series withdrawal sleeve is a steel part that threads into the threaded hole on the shaft to facilitate the removal of bearings with a tapered bore. It is used when the bearing is mounted with interference and cannot be removed with conventional pullers. MR Accesorios Industriales carries this series, with sizes for different shaft diameters.

The AOH series designation is read with the number that follows, which indicates the sleeve size. For example, AOH 2238, AOH 2244, AOH 2344, AOH 2348, AOH 3044, AOH 3048, AOH 3052 and AOH 3056 cover a range of sizes for shafts of different diameters. The number is not arbitrary: it relates to the bearing it helps to remove, so it is advisable to verify compatibility before choosing. If you have doubts, send us the bearing part number and we'll guide you.

These sleeves are used in industries where tapered roller bearings are commonplace: cement plants, mining, steel, paper, sugar and flour mills. Also in power transmission equipment, gear reducers and heavy machinery. In Argentina, they are commonly found in mill maintenance, high-flow pumps and industrial fans. Their function is to prevent damage to the shaft and the bearing during removal, which is critical when the equipment cannot be stopped for long.

To select the correct sleeve, take into account the diameter of the bearing's tapered bore and the type of shaft thread. Assembly requires cleaning the thread and adequate lubrication so as not to damage the splines. Aligning the sleeve with the shaft is essential: if it cross-threads, you can ruin the thread or deform the bearing. Follow the manufacturer's instructions and use the appropriate assembly tools. If you have any doubts, ask us.

As for equivalents, other manufacturers offer sleeves with similar designations, but they are not always interchangeable. Differences may be in thread pitch, length or surface treatment. Therefore, even if the code looks similar, always verify the critical dimensions. At MR Accesorios Industriales we can help you compare and find the part you need, with no obligation.

If you already have the sleeve or bearing part number, send it via WhatsApp to MR Accesorios Industriales and we'll quote you promptly. Don't hesitate to ask us about alternatives for your equipment.

The SKF HMV …E series hydraulic nut is a mounting and dismounting device that threads onto the shaft or adapter sleeve and generates oil pressure to expand the fitted part. It is used when the interference fit is too large to mount by impact or with a press, and allows work with control and without damaging the seat surfaces. MR Accesorios Industriales carries it as part of its mounting line.

The designation HMV …E is read as follows: HMV identifies the SKF hydraulic nut family, the number that follows indicates the thread size and the suffix E corresponds to the variant with a connection for pressurized oil. In the series examples, such as HMV 10E, HMV 12E or HMV 17E, the central number changes according to the thread diameter and the shaft range each model covers. To choose the correct one, you must match the nut thread with that of the shaft or sleeve where it is mounted.

These nuts are used in process industries, steel, cement, mining, paper and power generation, where large bearings are mounted with interference on shafts or adapter sleeves. They also appear in maintenance shops that dismount and remount rotating equipment: mills, gearboxes, fans, large pumps and paper machines. In Argentina they are common during plant shutdowns and in repair services for critical equipment, where mounting with a press is not viable due to size or access.

To select the nut, you must verify the shaft or sleeve thread, the diameter and pitch, and the expansion range the part requires. Mounting is done with hydraulic oil at the pressure specified by the manufacturer for that model; that pressure must not be exceeded and contaminated oils must not be used. Before mounting, clean the thread and the seat, check that the nut threads on by hand and check the alignment. Thread lubrication and sealing of the connection are key for the pressure to be transmitted without leaks.

As for equivalents, each manufacturer has its own nomenclature for hydraulic nuts and codes should not be cross-referenced by similarity. Interchangeability is defined by the thread, pitch, working pressure and expansion range, not by the trade name. If you have a nut from another brand, send us the thread data and the shaft or sleeve dimensions and we will help you find the equivalent SKF model within the HMV …E series.

To request a quote, send us by WhatsApp the complete code shown on the part or on the drawing, for example HMV 12E, along with the shaft or sleeve thread and a photo if possible. At MR Accesorios Industriales we cross-reference that data with the HMV …E series and confirm the model that corresponds. If you cannot find the code, tell us the thread diameter and pitch and we will locate it by size.

SKF HMV references ending in /233983 identify spare seal kits for hydraulic nuts. The photo shows O-rings: the item listed is the sealing spare part, not the complete hydraulic nut.

To order this spare part, keep the complete designation, including the size number and the /233983 suffix. For example, HMV 13/233983 identifies a seal kit; it must not be confused with an HMV 13 nut or with another reference sharing the same prefix. Matching the letters HMV alone is not enough to select the spare part.

Before requesting a quote, verify the part number of the nut in which the kit will be used. You can also send us a photo of its identification and of the removed spare part. The image on the product page helps identify the type of part; it cannot be used as a scale to infer diameters, ring cross-section or material.

Confirm with the technical team the kit's correspondence, the parts included and the replacement instructions applicable to your nut. If you need the complete tool, state it expressly in your inquiry. To request a quote from MR, send us the reference, the quantity and the nut data via WhatsApp or email.

The SKF HMVC …E series hydraulic nut is a precision tool used to mount and dismount bearings, sleeves and other components with a press fit on shafts or in housings. Its hydraulic design allows a controlled and uniform axial force to be applied, preventing damage to parts and facilitating work in tight spaces. It is a reliable solution for maintenance workshops and industrial plants that require fast and safe interventions.

The designation HMVC …E is interpreted as follows: the letters HMVC identify the SKF hydraulic nut family, while the number that follows indicates the size or application range. For example, models HMVC 18E, HMVC 22E and HMVC 28E correspond to different capacities, and the suffix E indicates a construction variant within the series. This nomenclature allows you to quickly select the right nut according to the shaft diameter or the component to be mounted.

These hydraulic nuts are used in a wide variety of industries in Argentina, such as metallurgy, cement, mining and power generation. They are common in the mounting of large bearings in mills, crushers, pumps, fans and paper machines. They are also used in the maintenance of rotating equipment where bearings must be dismounted without damaging them, especially when access is limited and considerable extraction force is needed.

To select the right hydraulic nut, take into account the shaft diameter, the type of bearing or sleeve to be mounted and the working pressure of the hydraulic system. It is essential to verify compatibility with the available pump and couplings. During mounting, ensure correct alignment and apply pressure gradually to avoid deformation. Lubrication of threads and contact surfaces contributes to smooth operation and extends the tool's service life.

Regarding equivalents and interchangeability, SKF HMVC …E series hydraulic nuts can replace other brands that use the same thread system and standardized dimensions. However, it is important to verify technical specifications and pressure ranges before substituting one tool for another. MR Accesorios Industriales supplies this line as an official brand, guaranteeing original products and SKF support.

If you need a hydraulic nut for your application, send the complete part number via WhatsApp to MR Accesorios Industriales. Our technical team advises you to choose the correct model and coordinate a quote with no obligation.

The SKF MB series lock washer is a fastening component used together with a slotted lock nut to secure bearings and other elements on threaded shafts. Its design with an inner tab and several outer tabs allows positive locking: one tab sits in the shaft groove and another is bent into a notch on the nut. This prevents the nut from loosening due to vibration or rotation. MR Accesorios Industriales carries this series as part of its line of bushings and adapter sleeves.

The MB series designation is read as MB followed by a number indicating the size. For example, MB 0, MB 1, MB 2, MB 3, MB 4, MB 5, MB 6 and MB 7 cover an increasing range of diameters. The number is not a direct measurement, but a code that corresponds to the lock nut of the same series. Each washer has an inner tab that fits into the shaft groove and several outer tabs that are bent over the notches on the nut. The numeric suffix lets you select the right washer according to the nut size.

SKF MB series lock washers are used in a wide variety of industrial applications in Argentina. They are found in gearboxes, pumps, fans, conveyors and process machinery, where they secure bearing lock nuts on shafts. They are also used in mining, cement, steel and food equipment. By securing the nut, they prevent loosening and maintain bearing preload, which extends the service life of the assembly. They are common in plant maintenance and equipment manufacturing.

To select the correct washer, take into account the size of the lock nut you are going to secure: the MB series corresponds to SKF KM nuts. Check that the inner tab fits into the shaft groove and that the outer tabs align with the notches on the nut. During assembly, bend one outer tab toward the nut with a suitable tool, without damaging the thread. It is important that the washer seats correctly and that the nut is in the desired position. Lubrication of the assembly and cleanliness of the threads also affect the result.

As for equivalents, SKF MB series lock washers are interchangeable with those from other brands that follow the same dimensional designation. However, not all brands use the same code; therefore it is advisable to verify the critical dimensions: inner diameter, outer diameter, thickness and number of tabs. If you need to replace a washer, send us the original part number and the shaft and nut measurements. At MR Accesorios Industriales we can guide you to find the equivalent part.

If you have doubts about which lock washer you need, send the nut part number or the shaft measurements via WhatsApp to MR Accesorios Industriales. We'll quote you the SKF MB series and advise you so that the fastening is safe and long-lasting.

The SKF W series lock washer is a fastening component placed between the lock nut and the bearing to prevent the nut from loosening due to vibration. Its design with an inner and outer tab allows the nut to be locked in the desired position. It is used in bearing assemblies mounted on shafts, where secure adjustment is critical.

The W series designation is read as W followed by a two-digit number indicating the size. For example, W 00, W 02, W 03, etc. Each code corresponds to a specific combination of bore diameter and thickness, intended for nuts with different threads. The numeric suffix does not indicate the diameter directly; you must consult the dimension table for each case. At MR we provide the exact equivalent for the code you send us.

These washers are used in industries such as food, cement and mining, and in maintenance workshops for rotating equipment. They are common in gearboxes, pumps, fans and conveyors, where bearings operate under load and vibration. They are also found in machine tools and continuous process equipment. In Argentina, they are frequently requested for repairs of imported equipment that uses SKF bearings.

To select the correct washer, take into account the shaft diameter, the nut thread and the available space. The inner tab must fit into the shaft groove and the outer tab must be bent over one face of the nut. It is important that the washer has the right thickness so that the nut seats properly. During assembly, check that the tab is not damaged and that the bend is firm but not excessive. Lubrication of the assembly also affects service life.

As for equivalents, other brands make lock washers with similar designations, but they are not always interchangeable. The critical dimensions are the bore diameter, outer diameter and thickness, as well as the position of the tabs. If you need to replace a washer, the best option is to compare it with the original part or consult us. We do not invent codes: we ask for the SKF code or the dimensions to give you the correct option.

If you already have the code for your SKF lock washer, send it by WhatsApp to MR Accesorios Industriales and we will quote you. If you do not have it, send us the shaft and nut dimensions and we will help you identify it. We work with the SKF line and can advise you so that the assembly is secure.

SKF MS designations correspond to lock clips for lock nuts. They are locking elements secured with a screw. They are identified by their full code and by the lock nut they work with.

The series includes designations with numbers, slashes and hyphens, such as MS 3052-48 and MS 30/500-96. Those characters are part of the designation and must be kept when requesting a quote. Do not infer the dimensions of the part from a fragment of the code or replace it with another that shares only the MS prefix.

The MS lock clip locks the lock nut: it fits into the groove of the adapter sleeve or shaft and is screwed to the face of the lock nut with a screw and washer.

To verify the part, send the full code of the lock nut and the existing clip. A photo of the assembly helps identify the mounting, but it does not replace the dimensional and compatibility check. Installation must follow the manufacturer's instructions for the selected combination. At MR you can check the designation and the required quantity via WhatsApp or email.

The SKF inch adapter sleeve, SNW series, is a key component for mounting bearings with tapered bore on cylindrical shafts. It is widely used in applications requiring secure and adjustable fixation, such as in transmissions, pumps and industrial equipment. MR Accesorios Industriales sells this line as an official brand, with more than 80 years of experience in the industry.

The SNW designation corresponds to SKF inch adapter sleeves. The number that follows indicates the shaft diameter in inches, and the decimal part specifies the exact size. For example, SNW 10X1.11/16 is for a 1 inch and 11/16 shaft, while SNW 13X2.3/16 corresponds to 2 inches and 3/16. This nomenclature allows quick identification of the required size without ambiguity.

These adapter sleeves are used in a wide variety of industries in Argentina, such as food, petrochemical, mining and metallurgical. They are common in power transmission equipment, centrifugal pumps, fans and conveyors, where bearings need to be mounted on unmachined shafts. Their design facilitates adjustment and removal, which reduces maintenance times.

To select the appropriate adapter sleeve, it is essential to verify the shaft diameter and the type of bearing to be mounted. The adapter sleeve is placed on the shaft and secured with a lock nut, which must be tightened with the appropriate wrench. It is important to lubricate the threads and contact surfaces before mounting, and ensure correct alignment to avoid undue axial loads. Subsequent sealing will depend on the working environment.

Regarding equivalences, SKF SNW series adapter sleeves are interchangeable with those of other brands that follow the same inch standard, such as Timken or NSK, as long as the dimensions match. However, it is recommended to verify tolerances and material, as they may vary between manufacturers. MR Accesorios Industriales offers advice to choose the correct option for each application.

If you need an inch adapter sleeve, at MR Accesorios Industriales you can request a quote quickly. Send the exact code, such as SNW 17X3, via WhatsApp and we will respond shortly. With more than 80 years in the market, we guarantee quality products and the technical support your project needs.

The SKF hydraulic sleeve of the OH..H series is a key component for mounting and dismounting bearings with a tapered bore. It is used in applications where secure and precise fastening is required, facilitating maintenance tasks and reducing the risk of damage to the shaft and the bearing. Its design allows hydraulic pressure to be applied to achieve a firm and controlled fit.

The designation OH … H is interpreted as follows: the letters OH indicate that it is a hydraulic sleeve, the number that follows is related to the shaft diameter and the suffix H indicates that the sleeve is designed to be mounted with the help of hydraulic pressure. For example, model OH 2344 H corresponds to a sleeve for a shaft of a certain size, and OH 3048 H for another. Each code identifies a specific size within the series, so it is essential to verify the exact designation when selecting the replacement.

These sleeves are used in a wide variety of industries in Argentina, such as metallurgy, cement, mining and food processing. They are common in rotating equipment such as mills, crushers, conveyor belts and machine tools, where bearings must be mounted with controlled interference. They are also used in applications where frequent dismounting is necessary for predictive maintenance, as they allow pressure to be released gradually and safely.

To select the appropriate sleeve, it is essential to know the shaft diameter and the type of bearing to be mounted. Mounting requires thorough cleaning of the surfaces, verification of the taper and use of compatible hydraulic oil. Proper lubrication and pressure control are critical factors to avoid deformation. In addition, correct alignment between the sleeve and the bearing must be ensured to guarantee long-term operation without vibration.

Regarding equivalences and interchangeability, SKF hydraulic sleeves of the OH..H series can be found in other brands under similar designations, but it is important to verify the exact dimensions and tolerances before replacing one with another. Not all sleeves are interchangeable with each other, as they may vary in diameter, length and thread. Therefore, we always recommend consulting a specialist and providing the complete code of the original product.

If you need a quote for an SKF hydraulic sleeve of the OH..H series, at MR Accesorios Industriales we advise you. Send us the exact code via WhatsApp and we will respond promptly with the information you need for your application.

The SKF hydraulic sleeve of the OH HTL series is a mounting tool designed to facilitate the installation and removal of bearings with a tapered bore. It works by means of injected oil pressure, which reduces effort and prevents damage to the bearing and the shaft. It is a practical solution for industrial maintenance workshops that need precision and care in every intervention.

The designation of the OH HTL series is interpreted as follows: the letters OH identify a hydraulic sleeve, the acronym HTL indicates that it includes a manual pump and hoses for oil injection. The number that appears between both parts, as in the example OH 3144 HTL, corresponds to the specific size of the sleeve and is related to the diameter of the tapered bore of the bearing to be mounted. Knowing this reference is key to selecting the correct accessory.

In Argentine industry, these sleeves are used in maintenance of heavy equipment, mills, conveyor belts, pumps and gearboxes. They are common in cement, steel, paper plants and in the oil & gas sector, where large bearings must be mounted with methods that guarantee a correct fit without damaging the raceways. They are also used in agricultural and road machinery repair workshops.

To choose the right sleeve, take into account the diameter of the tapered bore of the bearing and the type of mounting. The OH HTL series includes a manual pump that generates the oil pressure necessary to expand the sleeve and facilitate sliding. It is essential to clean the surfaces, apply the recommended lubricant and follow the mounting procedure to avoid deformations. Correct alignment and control of internal clearance ensure prolonged operation.

SKF hydraulic sleeves are compatible with bearings from other brands that have a tapered bore and equivalent dimensions. When looking for a replacement, verify that the sleeve designation matches that of the bearing to be mounted, since interchangeability depends on standardized dimensions. At MR Accesorios Industriales we sell the SKF brand and can advise you on equivalence with other references.

If you need to mount or dismount bearings with a tapered bore, a hydraulic sleeve simplifies the task and protects the components. At MR Accesorios Industriales we have more than 80 years of experience in industrial distribution. Send us the sleeve or bearing code by WhatsApp and we will quote you shortly.