FAG in agriculture: components for harvesters, seeders, norias and storage plants, and how to quote them

In agriculture, FAG special bearings solve assemblies where a standard bearing is not enough. In harvesters and seeders, for example, they appear in drive shafts and working components. We market FAG special bearings to replace the part your equipment carries originally.

To identify them, check the code engraved on the ring or packaging. Examples such as AMS20, AMS40 or AMS60 are references of FAG special bearings. If the part is very deteriorated, measure inner diameter, outer diameter and width, and note any visible mark. With that data we quote the exact replacement.

When ordering these bearings, a common mistake is confusing them with standard series due to similar dimensions. That is why it is always better to quote with the complete code. Send us a photo of the part and the code if you see it, and we will quote the component that corresponds to your equipment.

FAG spherical roller bearings are a robust option for harvester shafts, augers and transmission systems that work with heavy loads and some misalignment. Their double-row roller design allows absorbing shaft deviations without losing load capacity. In norias and grain elevators, they support pulleys and drums with constant demand.

Identification of these bearings is done by the code, which usually starts with 2 and has additional letters. For example, 23952-MB, 23972-MB and 23964-MB are FAG spherical roller bearing references that we distribute for agriculture. If you cannot find the code, measure the bore, outer diameter and width, and check whether the bore is cylindrical or tapered.

A frequent mistake when replacing a spherical roller bearing is choosing one with incorrect internal clearance. For agricultural applications with temperature changes, C3 clearance is sometimes required. Consult us with the code of your current bearing and we will indicate the appropriate variant. It is also key to verify the fit on the shaft and in the housing to avoid premature failures.

FAG cylindrical roller bearings are used in gearboxes, reducers and agricultural machinery transmissions where there are high speeds and radial loads. Their design allows dismounting the inner or outer ring depending on the assembly, which facilitates maintenance. In storage plants, they appear in large motors and pumps.

To quote these bearings, you need the complete code, which usually includes letters such as NNC and a number. Examples from our FAG line are NNC4920V, NNC4912V and NNC4930V. If the code is erased, accurately measure the inner diameter, outer diameter and width, and observe whether it has a sheet metal or solid cage.

When ordering a cylindrical roller bearing, a common mistake is not specifying the cage type or ring design. Send us a photo of the bearing and its location on the machine, and we will quote the correct FAG reference for your application.

FAG tapered roller bearings are typical in wheel hubs, disc hubs and seeder shafts. They support combined radial and axial loads, and are mounted in pairs to adjust preload. In harvesters, they appear in tensioner pulleys and intermediate transmissions. We distribute FAG tapered roller bearings for agricultural equipment.

Identification is done by the code, which is usually a five-digit number or a combination with slashes. For example, 32326, 32344 and 32920 are FAG tapered roller bearings that we market. If you do not have the code, measure the inner diameter, outer diameter and total width, and if possible the cone angle.

A common mistake when replacing tapered roller bearings is not respecting the preload adjustment. If it is too loose or too tight, service life is shortened. When quoting, indicate whether the bearing works in a wheel hub or in a transmission, and whether it has seals or adjustment washers. With that data we help you choose the appropriate FAG reference.

FAG deep groove ball bearings are versatile and are used in electric motors, pumps, fans and low-load shafts in agricultural machinery. They support moderate radial and axial loads, and work well at high speeds. In norias and conveyors, they appear in free rollers and tensioners.

To identify them, look for the engraved code, which is usually a four-digit number and suffixes such as 2RS or 2Z. Examples from our FAG line are 6020, 6003 and 6021. If the code is not legible, measure inner diameter, outer diameter and width, and check whether it has rubber seals or metal shields.

When ordering a deep groove ball bearing, a frequent mistake is not indicating the seal type. 2RS have rubber seals on both sides and retain grease better; 2Z have metal shields and are for less contaminated environments. Send us a photo of the bearing and its application, and we will quote the FAG reference with the correct seal.

FAG angular contact bearings are used in pumps, compressors and spindles of agricultural machinery where there are significant axial loads. They are mounted in pairs or in tandem to support forces in both directions. In storage plants, they appear in large fans and extractors.

FAG axial ball bearings, on the other hand, support purely axial loads and are used in rotary tables, vertical augers and lifting systems. To quote these bearings, you need the complete code and, if possible, the mounting arrangement. We market FAG angular contact and axial ball bearings for the agricultural industry.

A common mistake when replacing an angular contact bearing is not respecting the mounting orientation. If the load direction is reversed, the bearing fails quickly. When ordering, indicate whether the bearing works alone or in a set, and whether it has preload. With that information we will quote the appropriate FAG reference for your equipment.

FAG self-aligning ball bearings are used in shafts with angular misalignment, such as augers, agitators and flexible transmission systems. Their double-row ball design with a spherical raceway in the outer ring allows absorbing deviations without generating excessive internal loads. In agriculture, they appear in norias, mixers and forage equipment.

Identification is done by the code, which usually starts with 1 or 2 and has suffixes such as K for tapered bore. If you do not have the code, measure inner diameter, outer diameter and width, and check whether the bore is cylindrical or tapered. We distribute FAG self-aligning ball bearings for agricultural machinery.

When ordering these bearings, a common mistake is not indicating whether the bore is tapered. Bearings with suffix K are mounted on an adapter sleeve, which changes the fit. Send us a photo of the part and its location, and we will quote the correct FAG reference for your application.