Blog
Browning dimensions: how to identify the code from the part and what data to send for a quote
How to read the code marked on a Browning housing, which dimensions to measure, and what data to send so we quote the correct part.
BROWNING catalog by part number
Technical team at MR Accesorios Industriales · Updated on November 18, 2026

How to read the code on a Browning housing
When you have a Browning housing in your hand, the first thing to look at is the body of the part. The complete code is usually marked there, combining letters and numbers, such as VPB-320 or PBE920x 2. That code is the most direct way to order the correct replacement, so it is best to copy it exactly as it appears, including hyphens, spaces, and final letters.
If the part is painted, dirty, or rusted, the marking may be covered. A wire brush or a cloth with solvent is usually enough to make it legible. Take a well-focused photo with good light from several angles, because sometimes the code is on the base and other times on a side or on the cap.
Do not try to infer the shaft size from the numbers in the code: each series has its own logic, and a wrong assumption leads to ordering the wrong part. The safe approach is to combine three pieces of information: the code you read, the dimensions you measure with calipers, and a photo of the assembly. With that, we confirm the model for you.
Y housings with Browning insert bearing
Y housings with insert bearing are one of the Browning lines we carry. They combine a housing with an insert bearing that mounts on the shaft and locks to it, so the assembly is ready to bolt to the machine structure. They are common in conveyors and in equipment where a practical mounting is sought.
Codes in this line include VPB-320, VPE-220, and VPB-323. All three belong to the family of Y housings with insert bearing, and each has its own dimensions. Instead of interpreting the letters or numbers, the most reliable approach is to compare them with the actual dimensions of your part: the shaft diameter and the distance between the mounting holes.
When requesting a quote for a Y housing, send us the complete code if you have it, or at least the shaft size and a photo of the part. It also helps to tell us whether the bearing has a rubber seal (2RS) or a metal cap (2Z), because that changes the protection against dust and moisture. With that data we prepare your quote promptly.
Browning PBE series housings
In addition to Y housings, Browning's catalog that we carry includes housings from another family, among them PBE920x 2, PBE920x 3, and PBE920Fx 3. These are housings for supporting shafts in transmission machinery, and they are identified by the complete code, which includes the final letters and the number separated by a space.
The difference between these variants is in the code itself, which is why it is important to request exactly the one shown on the part. A PBE920x 2 and a PBE920x 3 are not the same item even if they look alike at first glance, and the same goes for PBE920Fx 3. If in doubt, send us a photo and we will compare it with the data sheet.
To quote a housing from this series, measure the shaft diameter, the distance between the holes in the base, and the height from the base to the shaft center. Add a front photo and a side photo. With that data and the marked code, we locate the model without you having to disassemble the whole machine.
Which dimensions to measure with calipers
When the code cannot be read, dimensions are the second path. With calipers, measure the shaft diameter where the housing is mounted, because that is the data that most defines which part fits. Measure in a clean, unworn area, and if possible, take the measurement at two points to detect whether the shaft is out of round.
Then measure the distance between the centers of the mounting holes in the base, both lengthwise and widthwise, and the height from the base to the shaft center. Write everything down in millimeters and note from which side of the part you took each measurement. A notebook or a photo with a ruler next to the part helps a lot.
With these dimensions and a photo of the part, our team can navigate the Browning line and propose the models that match. If you also send the partial code you can read, the search is even faster and the chances of error when ordering are reduced.
Clues from the insert bearing
In housings with insert bearing, the bearing itself may have a code engraved on the ring or on the seal. If you can see it without disassembling anything, write it down: it helps us locate the bearing series and dimensions, and from there it is easier to identify which housing holds it.
It is also useful to look at how the bearing locks to the shaft. Some use set screws and others use a different system, and they are not always interchangeable. A photo of the side of the bearing, where the locking points are visible, lets us detect the system your part uses.
Also check whether the bearing has a rubber seal (2RS) or a metal cap (2Z), and whether the outer ring is spherical or cylindrical. All these details can be seen in a clear photo. If you cannot remove the bearing, send us an image of the assembled unit and our technical team will identify it.
What data to send to quote a Browning housing
To quote, the ideal is to send the complete code shown on the part, for example VPB-320 or PBE920x 2. If you do not have it, send the main dimensions: shaft diameter, distance between mounting holes, and height to the shaft center. A photo of the part, even if worn, helps a lot to confirm the model.
It also helps to tell us which machine the housing is mounted on and what brand and model of housing it had before. If the original was from another brand, send us that code and we will see how to locate it within what we carry from Browning. You do not need to disassemble everything: a photo and one or two dimensions are enough to start.
Specify whether you need the complete assembly or only one part, and whether the bearing should have a rubber seal (2RS) or a metal cap (2Z). You can write to us via WhatsApp or email with the code, the dimension, or a photo, and we will reply promptly from Buenos Aires, Argentina.
Common mistakes when ordering a Browning housing
One of the most frequent mistakes is copying the code incorrectly: omitting a hyphen, a space, or the final letter. Between PBE920x 3 and PBE920Fx 3 there is one letter of difference and they are different items. That is why it is best to photograph the marking and send it along with the text you wrote, so we can verify it.
Another mistake is measuring the housing and not the shaft, or vice versa. To identify the part, both are needed: the shaft diameter and the base dimensions. If you send only one, the search remains open and we have to ask again. With both plus a photo, it is resolved in a single exchange.
Finally, do not assume that two similar housings are interchangeable. Those in the Y line with insert bearing and those in the PBE series have different shapes and mountings, and the base dimensions may not match. If in doubt, ask us before buying and we will help you confirm the exact model with the data from your part.
Frequently asked questions
How do I know which Browning housing I need?
The safest way is to read the code marked on the part, such as VPB-320 or PBE920x 2. If it cannot be read, measure the shaft diameter and the distance between the mounting holes, send us a photo, and we will help you identify it.
Can I infer the shaft size from the code?
It is not advisable. Each series has its own logic, so the reliable approach is to measure the shaft with calipers and confirm the model with us before ordering.
Which Browning lines do you carry?
Among others, Y housings with insert bearing, such as VPB-320, VPE-220, and VPB-323, and PBE series housings, such as PBE920x 2, PBE920x 3, and PBE920Fx 3.
What data do I need to request a quote?
The complete code, or the shaft diameter, the distance between the base holes, and a photo. Also specify whether the bearing has a rubber seal (2RS) or a metal cap (2Z).
How do I send you the inquiry?
Via WhatsApp or email, with the code, the dimension, or a photo of the part. We will reply promptly.
Keep reading
- Browning in Argentina: product guide, uses and how to get a quote by code
Discover the Browning lines we distribute in Argentina: Y housings with insert bearing and housings. We explain what each one is used for and how to get a quote by code or size.
- How to Read Browning Codes: Designation Structure, Prefixes, Suffixes, and Real Examples
A practical guide to understanding Browning nomenclature for housings and insert bearings. We show you how codes are built and what each part means.
- Browning by industry: where it is used, how to select it, mounting and maintenance
Practical guide to choose and maintain Browning housings and bearings in industrial applications. Selection criteria, correct mounting and care to extend their service life.
Continue here
Need a BROWNING quote?
Send us the BROWNING part number, the size or a photo of the part and we will get back to you with a quote.
