DODGE F4B-GTEZ-104S-SHCR flange bearing 4 holes
- Brand
- DODGE
- Category
- Bearing housings
- Subcategory
- Y-bearing unit
- Series
- GTEZ
We respond promptly.
Since 1945 · Martínez, Buenos Aires, Argentina
Request your quote via WhatsApp or email, with the quantity you need.
Can't find the exact model? Write to us with the part number or model you're looking for: we'll find it and quote it, even if it's not listed in the catalog.
Description
DODGE F4B-GTEZ-104S-SHCR is a reference of flange bearing 4 holes, within Bearing housings. Request a quote for F4B-GTEZ-104S-SHCR via WhatsApp or email with the quantity you need; we respond promptly with the quote and equivalents.
The DODGE GTEZ Y-bearing housed unit is a 4-bolt flange mounted bearing, designed to guide and support rotating shafts in industrial equipment. Its cast iron housing and sealed insert make it suitable for dusty, humid or moderately loaded environments. It is used in conveyors, agitators, pumps and process machinery, where firm fastening and simple mounting are required. MR Accesorios Industriales sells this line in Buenos Aires, Argentina.
The GTEZ series designation is read in blocks: the initial letters identify the housing type and the insert, while the numbers and suffixes indicate the shaft diameter and the sealing or locking variants. For example, in F4B-GTEZ-104S-SHCR, the F4B prefix corresponds to the 4-bolt flange, GTEZ defines the insert bearing series, 104S indicates the shaft diameter in inches and SHCR refers to the sealing and locking configuration. Knowing this logic lets you order the exact replacement by part number.
In Argentine industry, these housed units appear in belt conveyors, mixers, fans, centrifugal pumps and packaging lines. They are also found in food, chemical and water treatment plants, where the 4-bolt flange makes anchoring to metal structures or masonry easier. Their design allows shaft alignment with moderate tolerances and absorbs small misalignments, which reduces maintenance on continuously operating equipment.
To select the correct housed unit, take into account the shaft diameter, the type of load (radial, axial or combined) and the environmental conditions. The insert seal defines the protection against dust and liquids: in humid environments or with frequent washdowns, a configuration with an additional lip seal is preferable. Mounting requires a flat, clean surface, even tightening of the four bolts and proper lubrication before start-up. Check alignment with a straightedge or dial indicator to avoid stress on the insert.
Flange mounted bearings are interchangeable between brands if the flange dimensions, shaft diameter and locking type match. When requesting a quote, provide the full part number shown on the nameplate or on the old housing: with that we identify the GTEZ series and offer you the compatible alternative. If the equipment has a special variant, we quote it for you with the same performance.
MR Accesorios Industriales sells the DODGE line in Buenos Aires, Argentina, with technical advice so you can choose the right housed unit. Send us the part number on WhatsApp and we will quote it promptly, along with the lubrication and mounting accessories you need.
Dimensions
- Número de producto
- 129726
- Bore
- 1-1/4 in
Frequently Asked Questions
- How do I identify the GTEZ housed unit I need?
- Read the part number engraved on the housing or on the equipment nameplate. The GTEZ series and the shaft number (for example, 104S) define the replacement. Send it on WhatsApp and we will quote the exact reference.
- What is the difference between a flange mounted unit and a pillow block?
- The flange unit is bolted to a surface perpendicular to the shaft, while the pillow block rests on a parallel base. The choice depends on the space and the load direction. Both use similar inserts, but the anchoring differs.
- Do I need to lubricate the insert bearing when mounting it?
- Many inserts come pre-lubricated from the factory, but it is advisable to check the condition of the seal and add grease if the equipment has been stored for a long time. Use a grease compatible with the working temperature and do not mix different bases.