Skip to content
All products

Blog

Dodge dimensions: how to identify the code from the part and what data to send for a quote

We explain how to read the dimensions and markings of a Dodge part to identify the correct code and what information you should send us for a quote.

DODGE bearings in Argentina: guide and quotes

Technical team at MR Accesorios Industriales · Updated on November 15, 2026

Share on LinkedIn

Dodge dimensions: how to identify the code from the part and what data to send for a quote

Y bearings (inserts): how to read the code and dimensions

Dodge Y bearings, also called inserts, are ball bearings with a spherical outer ring and an extended inner ring. They are used mounted in Y housings and allow absorbing slight shaft misalignments. To identify them, look at the engraving on the inner or outer ring: it usually has a code like INS-ER-DL-102, INS-ER-DL-103 or INS-ER-DL-104. That code is the exact reference of the insert.

In addition to the code, it is advisable to measure the bore diameter in millimeters or inches, because many inserts are designated by shaft size. For example, an insert for a 1-inch shaft usually has a different code than one for 25 mm, even if they are similar. Also check whether the insert has a set screw, eccentric or adapter sleeve locking system, because that changes the reference.

When requesting a quote, send the full code if you see it, or at least the shaft dimensions and overall width. If you cannot find the code, a photo of the part with a ruler next to it helps a lot. Avoid confusing the insert with the housing: they are separate parts sold separately or as a set. We sell Dodge inserts and will indicate the exact reference.

Y housings with insert bearing: identification by dimensions and floor type

Dodge Y housings with insert bearing are complete units that include the cast iron or sheet metal housing and the corresponding insert. They are used in conveyors, fans, agricultural machinery and other equipment with long shafts. To identify them, look at the plate or engraving on the housing: you may find codes like 124610, 124611 or 124612.

In addition to the code, measure the height from the shaft center to the floor (center height), the distance between mounting holes and the shaft diameter. Those data define the housing series, such as floor, wall or take-up housing.

When quoting, send the housing and insert code if you have them, or the main dimensions. If the housing is broken or very worn, a photo of the assembly helps identify the series. Do not assume that all Y housings with the same shaft diameter are the same: center height and mounting type change. We sell Dodge Y housings and help you find the model.

Housings: how to distinguish models by shape and application

Dodge housings come in different types: floor, wall, take-up, flange and hanger. Each has a designation according to the series and the size of the bearing it houses. It is key to identify the type correctly because they are not interchangeable.

To identify a housing, look at the general shape and how it is fixed to the structure. For example, a floor housing has two holes in the base, while a wall housing has holes on one side. Also measure the distance between holes and the diameter of the bearing seat. Those data allow you to find the correct code in the catalog.

When requesting a quote, send front and side photos with a ruler, and if possible, the code engraved on the part. Avoid ordering only by shaft diameter, because the same shaft can use housings of different series. We sell Dodge housings and guide you with the reference.

Pulleys: how to measure diameter, belt section and bushing

Dodge pulleys are used in V-belt or synchronous belt drives. To identify them, first measure the outside diameter and the width of the groove or face. Also count the number of grooves if it is for V-belts. If the pulley has an engraved code, write it down: for example MA30, MA50 or MA15 are Dodge pulley codes.

Another important datum is the bushing type and size, which defines compatibility with the shaft. Measure the bushing bore diameter and check whether it has a keyway. If the pulley is mounted, you can measure the shaft diameter and the distance between groove centers.

When quoting, send the pulley code if you see it, or the diameter, width and bushing type dimensions. A photo of the pulley with a ruler helps confirm the series. Do not forget to indicate whether it is for classic V-belt, narrow profile or synchronous, because the design changes. We sell Dodge pulleys and quote the one you need.

Reducers: how to identify the model by plate and ratio

Dodge reducers are transmission units that reduce speed and increase torque. They come in different types: worm gear, helical, shaft-mounted, etc. To identify them, look for the nameplate, which usually has the model and serial number. For example, you may find codes like Maxum XTR 60, Maxum XTR 80 or Maxum XTR 50.

In addition to the model, note the reduction ratio, the flange or output shaft size and the mounting position. Those data are essential to identify the unit. If the plate is illegible, measure the distance between shaft centers and the shaft diameters, and take photos of the complete reducer.

When quoting, send all the nameplate information and the main dimensions. If the reducer is coupled to a motor, also indicate the motor power and speed. Avoid ordering only by power, because there are many mounting and ratio variants. We sell Dodge reducers and help you identify the model.

Taper bushings and components: how to measure the taper and the bore

Dodge taper bushings are fastening elements used to mount pulleys, sprockets and other components on shafts. They are identified by a series code, such as 1008, 1210, 1615, etc., which indicates the bore diameter and taper size. That code is usually engraved on the front face of the bushing.

To measure a taper bushing, take the bore diameter (the hole for the shaft) and the outside diameter of the taper. Also count the number of threaded holes for the fastening screws. If the bushing is mounted, you can measure the shaft diameter and the major taper diameter, and compare with standard tables.

When requesting a quote, send the bushing code if you see it, or the bore and taper dimensions. A photo of the bushing with a ruler helps confirm the series. Do not confuse the taper bushing with a locking sleeve: they are different parts. We sell Dodge taper bushings and related components, and will indicate the reference.

Sprockets, chain wheels and belts: identification by pitch and number of teeth

Dodge sprockets and chain wheels are used in chain drives. To identify them, count the number of teeth and measure the chain pitch (distance between rollers). Also look at the bore diameter and hub type.

In the case of Dodge V-belts, measure the top width, height and outside or inside length. Also check the profile: classic (A, B, C, D) or narrow (3V, 5V, 8V). Belts usually have the code printed, but if it is worn off, the dimensions allow you to identify it.

When quoting, send the code if you see it, or the teeth and pitch data for sprockets, or profile and length for belts. A photo with a ruler helps confirm. Avoid ordering only by the outside diameter of a sprocket, because the number of teeth and pitch define the reference. We sell Dodge sprockets, chain wheels and V-belts.

Frequently asked questions

How do I identify the code of a Dodge insert bearing?

Look for the engraving on the outer or inner ring, for example INS-ER-DL-102. If it is not legible, measure the bore diameter and width, and check the locking system. With that data we help you identify the code.

What dimensions do I need to quote a Y housing with bearing?

You need the center height, the distance between mounting holes and the shaft diameter. The housing code, such as 124610, and a photo of the assembly also help.

How do I know which Dodge pulley I have if it has no code?

Measure the outside diameter, face width, number of grooves and bushing type. With that data and a photo we help you identify the code.

What data from a Dodge reducer should I send for a quote?

Send the model from the nameplate, the reduction ratio, shaft sizes and mounting position. If the plate is illegible, measure center distance and diameters, and take photos.

How do I identify a Dodge taper bushing?

Look at the code engraved on the front face, such as 1008 or 1210. If it is not there, measure the bore diameter and the major taper diameter, and count the threaded holes.

Products with photos in the catalogue

Keep reading

Continue here

Need a DODGE quote?

Send us the DODGE part number, the size or a photo of the part and we will get back to you with a quote.

See DODGE at MR

Request a DODGE quote on WhatsApp
Request a quote on WhatsApp